Abstract:The research study explored the impact of magnesium on the microstructural characteristics and mechanical properties of Al-Mg-Mn alloy in both its as-cast and homogenized states. Various analytical techniques including optical microscopy, x-ray diffraction, scanning electron microscopy, energy-dispersive x-ray spectroscopy, Vickers microhardness testing, and electrical conductivity measurements were employed for the analysis of the Al-Mg-Mn alloy. The findings reveal that the primary phases present in the as-cast alloy consist of α-Al, β ( ), and . As the magnesium content increases, notable alterations are observed in the diffraction angle θ, inter-planar spacing d, lattice constant a, and the solute magnesium concentration in the α-Al matrix. In instances where the Mg content is low, the grain size and distribution in both the as-cast and homogenized alloys appear coarse and uneven. However, as the magnesium content rises, there is a reduction in the primary dendrite length and columnar crystal zone in the as-cast alloy, alongside enhanced development of secondary dendrites and gradual diminishment of the grain size. This reduction in grain size is particularly pronounced in the homogenized alloy. Additionally, the hardness of both the as-cast and homogenized alloys experiences an increase, while the electrical conductivity undergoes a decrease with escalating magnesium content. Notably, in comparison with the as-cast alloy, the hardness and electrical conductivity of the homogenized alloy exhibit enhancements. The outcomes of this study offer valuable insights for the subsequent processing and deformation applications of the Al-Mg-Mn alloy.

Microstructure and Mechanical Properties of High Strength and Toughness Die Casting Al-Mg-Si-Mn Alloys

Microstructure and mechanical properties of high strength die-casting Al-Mg-Si-Mn alloy

Effect of Zn Concentration on the Microstructure and Mechanical Properties of Al-Mg-Si-Zn Alloys Processed by Gravity Die Casting

Microstructure, Mechanical Properties and Die-Filling Behavior of High-Performance Die-Cast Al–Mg–Si–Mn Alloy

Melt Superheating on the Microstructure and Mechanical Properties of Diecast Al-Mg-Si-Mn Alloy

Influence of the Mg Content on the Microstructure and Mechanical Properties of Al-xMg-2.0Si-0.6Mn Alloy

Effect of Mg Level on the Microstructure and Mechanical Properties of Die-Cast Al–Si–Cu Alloys

Effects of Mg on the Microstructure and Mechanical Property of Al-Si-Mg Casting Alloys

Microstructure and Tensile Properties of Al-Mg-Mn Alloy

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Influence of Varied Mg/Si Mass Ratio on the Microstructure and Mechanical Properties of Aluminum Die Casting Alloys

Effect of Mg addition on microstructure and mechanical properties of Al-Si-Cu-Fe alloy with squeeze casting

Microstructure and Tensile Properties of the Mg-6Zn-4Al-xSn Die Cast Magnesium Alloy

Effect of Alloying with Al, Nd and Ca and Heat Treatment on Microstructures and Mechanical Properties of Vacuum Die-Cast AM50 Alloy

Effects of Al Concentration on Microstructure and Mechanical Properties of Mg-xAl-1Zn-1Si Alloy

Effects of magnesium and copper additions on tensile properties of Al-Si-Cr die casting alloy under as-cast and T5 conditions

Synergistic Effects of Mg Alloying and Subsequent Homogenization Treatment to Improve the Microstructure and Properties of Al-Mg-Mn Alloys

Effects of Mg content on microstructure and mechanical properties of low Zn-containing Al−xMg−3Zn−1Cu cast alloys

Effects of Adding Trace Modification Elements and Heat Treatment on the Strength and Toughness of AlSi8Cu2MgMn Alloy

Effects of Mn Content on Microstructure and Mechanical Properties of Mg-Zn-Mn Wrought Alloys

Macro-heterogeneities in microstructures, concentrations, defects and tensile properties of die cast Al–Mg–Si alloys