Abstract:In recent years, inspired by “biomimicry”, superhydrophobic surfaces have gained significant attention. Superhydrophobic surfaces demonstrate notable advantages in addressing interfacial issues, and superhydrophobic coatings exhibit excellent waterproofness, anti-fouling, self-cleaning, anti-corrosion, and additional capabilities, making them promising next-generation waterproof materials. However, the complex preparation process, coupled with poor wear resistance and environmental durability, severely limits their practical applications. Therefore, this article started from simplifying the preparation process and improving the durability of the coatings. Epoxy resin (E51) was used as the film-forming material, and carbon nanotubes (CNTs) and dual-sized SiC particles (nano-SiC and micro-SiC) were used as the fillers. Room temperature vulcanized silicone rubber (RTV) was used as a binder interacting with epoxy resin to promote the interface interaction between the fillers and the polymers. This process resulted in the successful preparation of superhydrophobic coatings with outstanding comprehensive performance. When the ratio of μ-SiC to n-SiC was 1:1, the prepared coating exhibited the best superhydrophobic properties with a water contact angle (WCA) of 167.4° and a sliding angle (SA) of 4.6°. Even after undergoing severe mechanical tests, such as sandpaper abrasion for 1000 cycles, sand impact for 100 cycles, cross-cut test, and tape-peeling for 70 cycles, the coatings still maintained their non-wetting Cassie-Baxter state. Furthermore, even after immersion in strong acid, strong alkali and 3.5 wt% NaCl solutions for 6 days, keeping at 500 °C for 2 hours, and exposure to ultraviolet for 6 days, the coatings still exhibited excellent superhydrophobicity. This suggested that the prepared coating had excellent chemical stability and high-temperature resistance. In addition, the superhydrophobic coating exhibited exceptional capabilities in self-cleaning, anti-corrosion, anti-icing, and de-icing properties. Furthermore, this coating, applicable to diverse substrates including board, steel, paper, and glass, demonstrated an impressive water contact angle (WCA) and sliding angle (SA). The spraying method offers the benefits of simplicity and cost-effectiveness. This is poised to significantly broaden its practical applications in various fields, including construction, transportation, and the chemical industry.

Improved Surface Wettability of Water by Applying SiC/Ti6Al4V Coatings on Carbon/Carbon Composites

Influence of multi-interfacial structure on mechanical and tribological properties of TiSiN/Ag multilayer coatings

Influence of Carbon Contents on the Structure and Tribocorrosion Properties of Tisicn Coatings on Ti6al4v

Improvements of the interfacial adhesion between water-based coating and carbon fiber reinforced polymer composite by deposition of silica particles

Tribological behaviors of TiSiC coating in seawater environment

Microstructure, Mechanical and Tribological Properties of CrSiC Coatings Sliding Against SiC and Al2O3 Balls in Water

Interfacial Modification and Performance Enhancement of Carbon Matrix/aluminum Composites

Improved antioxidative and mechanical properties of SiC coated C/C composites via a SiO2-SiC reticulated layer

Simultaneous improvement of interfacial bonding and thermal resistance of carbonaceous fiber/silicone composite coatings modified with aniline-methyl-triethoxysilane

Interfacial Reactions and Mechanical Properties Studies of C-Coated and C/B4C Duplex-Coated SiC Fiber-Reinforced Ti2AlNb Composites

Effect of SiC and TiC content on microstructure and wear behavior of Ni-based composite coating manufactured by laser cladding on Ti-6Al-4V

Self-densification behavior, interfacial bonding and cyclic ablation resistance of HfSi2-ZrSi2 modified SiC/ZrB2-SiC/SiC coating for Cf/SiC composite

Effect on Wetting Properties of the Al-Ti System by the Addition of Different Alloying Elements

Microstructure and Thermal Properties of Inert Plasma-Sprayed Tungsten Coating on SiC-Coated Carbon/Carbon Composites

Fabrication of high-durability superhydrophobic coatings based on dual-sized SiC particles

Design and fabrication of a stable Ni-PTFE-SiC superhydrophobic anticorrosive coating by electrodeposition

Role of Si in the wetting of TiC by Al

Achieving excellent wetting of inactive Ag on C/C composites by a low-temperature surface modification strategy

Influence of Trimethylsilane Flow on the Microstructure, Mechanical and Tribological Properties of CrSiCN Coatings in Water Lubrication

Facile Preparation of Robust Superamphiphobic Surface by Electrochemical Etching Process Based on the SiC/Al Composites

In-situ TiC-Ti5Si3-SiC composite coatings prepared by plasma spraying