Abstract:Zirconia‐toughened alumina (ZTA) ceramics with high mechanical properties were sintered by hot‐pressing method using SiC particles (SiCp) and SiC whiskers (SiCw) as the reinforcing agents simultaneously. The influences of sintering temperature, SiCp and SiCw contents on the microstructure and mechanical properties of ZTA ceramics were investigated. It was found that both SiCp and SiCw could contribute to grain refinement significantly and promote the mechanical properties of the ceramics. However, the excess addition of SiCp or SiCw led to the formation of pores with large sizes and degraded the mechanical properties instead. When 13 wt% SiCp was introduced, the maximum flexural strength of 1180.0 MPa and fracture toughness of 15.9 MPa·m1/2 were obtained, whereas the maximum flexural strength of 1314.0 MPa and fracture toughness of 14.7 MPa·m1/2 were achieved at 20 wt% SiCw. Interestingly, the simultaneous addition of SiCp and SiCw could further improve the mechanical properties, and the highest flexural strength of 1334.0 MPa and fracture toughness of 16.0 MPa·m1/2 were achieved at a SiCw/SiCp ratio of 16/4. The reinforcement mechanisms in the ceramics mainly included the phase transformation toughening of ZrO2, the crack deflection and bridging of SiCp and SiCw and the pull‐out of SiCw.

Effects of sintering velocity on the microstructure and mechanical properties of hot-pressed ZrB2-SiC-ZrO2f ceramics

Effect of sintering temperature and holding time on the microstructure and mechanical properties of ZrB2–SiCw composites

Effects of Short Carbon Fiber on Mechanical Properties of ZrB2-SiC Ultra-high Temperature Ceramics

Effects of SiC Platelet and ZrSi2 Additive on Sintering and Mechanical Properties of ZrB2-based Ceramics by Hot-Pressing

Mechanical Properties of Short Carbon Fiber Reinforced ZrB2–SiC Ceramic Matrix Composites

Effect of the Addition of Short Carbon Fiber on Thermal Insulation Properties of ZrB2- SiC Hot-Pressed Ceramics

Pressureless Sintering of Silicon Carbide Ceramics Containing Zirconium Diboride

Spark plasma sintering and hot pressing of ZrB2–SiCW ultra-high temperature ceramics

Effects of ZrB2 on Mechanical Properties of Al2O3-ZrB2-SiC Composite Ceramics at Room Temperature

Processing and Mechanical Properties of Short Carbon Fibers Toughened Zirconium Diboride-Based Ceramics

Preparation, mechanical properties, and toughening mechanisms of SiCw/SiCp‐reinforced zirconia‐toughened alumina ceramics

Microstructure and Mechanical Properties of Hot-Pressed Al2O3–mullite–ZrO2–SiC Composites

Characterization of hot-pressed short carbon fiber reinforced ZrB2–SiC ultra-high temperature ceramic composites

Microstructure and properties of silicon carbide whisker reinforced zirconium diboride ultra-high temperature ceramics

Effects of ZrB2 powders on microstructure and mechanical properties of ZrB2-SiCw ceramics

Processing, microstructure, and mechanical properties of chopped SiC fibers reinforced ZrB2–hBN–based composites

Study on Mechanical Properties of Hot Pressing Sintered Mullite-Zro2 Composites with Finite Element Method

Microstructure, mechanical and high-temperature dielectric properties of zirconia-reinforced fused silica ceramics

Preparation and flame ablation/oxidation behavior of ZrB2/SiC ultra-high temperature ceramic composites

Preparation and Characterization of ZrB 2 -Sic Ultra-High Temperature Ceramics by Microwave Sintering

Fabrication and mechanical properties of ZrB2–SiCw ceramic matrix composite