Abstract:Although <math>{101¯2}</math> twinning behavior has been extensively studied, it has rarely been investigated under biaxial tension. In the present research, the mechanical response and <math>{101¯2}</math> twinning behavior of a Mg AZ31 sheet under biaxial tension with various stress ratios (<math>σND:σTD</math>) along the normal direction (ND) and transverse direction (TD) were systematically studied. The results indicate that the yield stress along the ND is nearly independent of <math>σND:σTD</math>. Schmid law applied to <math>{101¯2}</math> twinning under biaxial tension yields better efficiency than that for uniaxial tension, and a higher efficiency is observed with a larger stress ratio along the TD; the fraction of experimentally observed twin variants with Schmid factors (SFs) of ranks 1 and 2 is approximately 45% for uniaxial tension, whereas it is approximately 68% for <math>σND:σTD=2:1</math> and approximately 88% for <math>σND:σTD=1:2</math>. This result contradicts with the previously reported result that Schmid law is more efficient for uniaxial stress states than under multiaxial stress conditions. It is found that biaxial tension will increase the difference in SF for the six twin variants and make Schmid law more efficient. Twin variant selection and volume fraction are highly dependent on <math>σND:σTD</math>. For uniaxial tension, the activities for the six variants are similar, and the (0002) poles of the twins are distributed evenly on a circle approximately 80°–90° away from the ND. In contrast, the variants <math>(01¯12)[011¯1]</math> and <math>(011¯2)[01¯11]</math> are more favorable under biaxial tension, and more (0002) poles of the twins concentrate around the rolling direction with a higher ratio of <math>σTD</math>. At a similar strain level, the twin fraction under biaxial tension is often different from that under uniaxial tension, and this difference varies with <math>σND:σTD</math>. This mechanism is associated with a stress-ratio-mediated detwinning behavior under biaxial tension. The findings in the present study provide a new and significant understanding of the twinning behavior of Mg alloys.

Reducing the Tension–compression Yield Asymmetry in a Hot-Rolled Mg–3Al–1Zn Alloy Via Multidirectional Pre-Compression

EBSD Analysis and Theoretical Prediction of Twin Orientations During Compression in Mg-3Al-1Zn

Effect of twinning on the deformation behavior of an extruded Mg-Zn-Zr alloy during hot compression testing

Twin recrystallization mechanisms in a high strain rate compressed Mg-Zn alloy

Study on twinning behaviors during multi-directional compression for AZ31 magnesium alloy by EBSD

Improvement of dynamic compression properties and strengthening mechanism of Mg–Y–Nd–Gd–Zr alloy by pre-twinning

Influence of precipitation on tension and compression twinning in Mg-6.5Zn alloy

{ 10 1 ̄ 2 } twinning behavior under biaxial tension of Mg–3Al–1Zn plate

Identification and Analysis of Twinning Variants During Compression of a Mg–Al–Zn Alloy

Reducing the Tension–compression Yield Asymmetry of Extruded Mg–Zn–Ca Alloy Via Equal Channel Angular Pressing

Promoting hybrid twins structure to reduce yield asymmetry of rolled AZ31 plates by combining side-rolling and torsion

Twinning Behavior, Microstructure Evolution and Mechanical Property of Random-Orientated ZK60 Mg Alloy Compressed at Room Temperature

On the strengthening and slip activity of Mg-3Al-1Zn alloy with pre-induced { 10 1 ̄ 2 } twins

A Study of {10-12} Twinning Activity Associated with Stress State in Mg-3Al-1Zn Alloy during Compression

Effect of pre-deformation on the activation stress of {10–12} twinning in Mg–3Al–1Zn alloy

Twinning Behavior of a Strongly Basal Textured AZ31 Mg Alloy During Warm Rolling

Effect of Local Stresses of Primary Twinning on Double Twinning, Twin Intersection and Their Competition

Influence of Grain Orientation on Twinning During Warm Compression of Wrought Mg–3Al–1Zn

Influence of In-Plane Simple Shear Strain on the Grain Orientation Regulation and Stretch Formability of Pre-twinned AZ31 Magnesium Alloy Sheet

Reducing the yield asymmetry in Mg-5Li-3Al-2Zn alloy by hot-extrusion and multi-pass rolling

The Dislocation-Twin Interaction and Evolution of Twin Boundary in AZ31 Mg Alloy