Abstract:Al-Cu alloys are widely applied in the automobile and aircraft industries because of their low density, good wear resistance, low cost, and excellent mechanical properties. Microalloying, particularly using Mn, can further enhance the mechanical properties. Thus, a combination of high-angle annular dark-field scanning transmission electron microscopy, STEM-EDX elemental mapping, and tensile tests were used to investigate the effects of Mn content on the nucleation, growth, and structural evolution of θ'-Al 2 Cu and Mn-rich precipitation phases of Al-4Cu- x Mn alloys ( x = 0.1 wt.%, 0.2 wt.%, 0.3 wt.%, and 0.5 wt.%). The results revealed that adding Mn to Al-Cu alloys can effectively promote the precipitation of θ'-Al 2 Cu; particularly, increasing Mn content from 0 wt.% to 0.2 wt.% reduced precipitate size and size distribution. Moreover, the 0.3-wt.% Mn addition reduced θ′-Al 2 Cu precipitation and coherent Mn-rich phase precipitation with butterfly contrast in the alloy. The addition of 0.5-wt.% Mn resulted in disappearance of the θ'-Al 2 Cu phase and precipitation of a rod-like Mn-rich phase in the alloy, which was found to have coherent and semi-coherent interfaces with an Al matrix. Promotion of precipitation and refinement in the θ′-Al 2 Cu phase is primarily attributed to the excellent miscibility and interfacial segregation of the Mn element, which effectively enhanced heterogeneous nucleation in the θ′-Al 2 Cu phase. Additionally, two morphologies of the Mn-rich phase exhibited a relatively large coherence area with the matrix relative to θ′-Al 2 Cu; thus, our study provides a new strengthening and toughening technique for Al alloys.

Effect of Mn concentration on the kinetics of strain induced precipitation in Ti microalloyed steels

Strain-induced Precipitation in a Ti Micro-Alloyed HSLA Steel

An Analytical Model for the Kinetics of Strain-Induced Precipitation in Titanium Micro-Alloyed Steels

Precipitation Behavior of Ti in High Strength Steels

Effect of V on the Precipitation Behavior of Ti−Mo Microalloyed High-Strength Steel

Effect of Molybdenum Addition on the Precipitation of Carbides in the Austenite Matrix of Titanium Micro-Alloyed Steels

Effect of Tungsten Addition on Continuous Cooling Transformation and Precipitation Behavior of a High Titanium Microalloyed Steel

Influence of Ti content on mechanical properties of low carbon steel

The investigation of precipitation behavior of titanium compounds for high titanium steel based on in situ observation

Strain-induced Precipitation Kinetics of Nb(C,N) and Precipitates Evolution in Austenite of Nb–Ti Micro-Alloyed Steels

Effect of Different Water Toughening Treatment on Mechanical Properties and Microstructure of Fe-Mn-C TWIP Steel

Effect of Manganese on the Microstructure and TiC Precipitation in Hypoeutectoid Steel

Revealing the influence of Mo addition on interphase precipitation in Ti-bearing low carbon steels

MICROSTRUCTURE, MECHANICAL PROPERTIES AND INTERPHASE PRECIPITATION BEHAVIORS IN V-Ti MICROALLOYED STEEL

Influence of Mn Addition on the Evolution of Precipitates in Al-Cu Alloys

Effect of Magnesium Content on Precipitation Behavior of TiN-Containing Inclusions in High-Titanium High-Strength Steel

The Significant Impact of Ti Addition on the Hot Deformation Behavior of Medium‐Manganese Microalloyed Steel

Effect of Zr on static recrystallization of deformed austenite and strain-induced precipitation in Ti microalloyed steel

Thermodynamic Research on the Precipitation of Ti2O3, TiN and TiC in Continuous Casting of Titanium Microalloyed Steel

Precipitation Behavior and Strengthening Effect of (Ti,Mo)C Particles in a Martensitic Steel

Effect of cobalt on precipitation in Fe-Cr-Co-Mo-Ni-C stainless steels