Abstract:Abrasive water jet (AWJ) is a type of cold processing technology, and there are many factors affecting its machining effect. In this paper, a coupled Finite Element Methods-Smoothed Particle Hydrodynamics (FEM-SPH) numerical model was established to investigate the key influencing factors of AWJ machining ductile materials. The abrasive particles in the model were shaped as irregular polyhedrons, and the material properties of the abrasive particles as well as the influence mechanism of the fluid–structure interaction between the abrasive particles and the water were considered. The relative error range of experimental measured results and simulation predicted results is 22.77%–36.55%. Then, the effects of content and distribution of abrasive particles, the jet working pressure P, the traverse rate of nozzle V t r a v and the impingement angle α were systematically and quantitatively evaluated through two-way verification of experiments and simulations. It was found that: (i) Effects of stand-off distance (SOD) on the kerf profile and the quality of kerf surface was essentially determined by the content and distribution of abrasive particles. As the increase of SOD, the jet divergence gradually increases, and the kerf profile gradually changes from “U-shaped” to “V-shaped”. (ii) Experiments and simulations demonstrate that the P has a linear increasing relationship with the maximum depth h of kerf profile, and the V t r a v has a linear decreasing relationship with the maximum depth h, while it has a linear increasing relationship with the jet trailing angle β , which was independent of the ductile material type. (iii) The combined effect of V t r a v and α affects geometric parameters and surface quality of the kerf profile, under the same P, the depth of the cut surface obtained by backward cutting is only 72.1% of that of the forward cutting, while the quality of the cut surface of former one is higher than the latter one.

An Investigation into the Radial-Mode Abrasive Waterjet Turning Process on High Tensile Steels

An Experimental Study on Radial-Mode Abrasive Waterjet Turning of Alumina Ceramics

Modeling of the Cutting Front Profile in Abrasive Water Jet Machining Based on the Energy Balance Approach

Optimization of Machining Parameters in the Abrasive Waterjet Turning of Alumina Ceramic Based on the Response Surface Methodology

Modeling of cutting of stainless steel AISI 304 by abrasive water jet

Enhancing High-Alloy Steel Cutting with Abrasive Water Injection Jet (AWIJ) Technology: An Approach Using the Response Surface Methodology (RSM)

Experimental Investigation into the Effect of Abrasive Process Parameters on the Cutting Performance for Abrasive Waterjet Technology: a Case Study

An Experimental Investigation on Machining of Hardened AISI 440C Stainless Steel Using Abrasive Water Jet Machining Process

Material Removal Analysis in the Radial-Mode Abrasive Waterjet Turning of Ceramic Materials

Analytical Modeling of Effective Depth of Cut for Ductile Materials Via Abrasive Waterjet Machining

Statistical modelling of depth milling in Ti-6AL4V using abrasive water jet machining

An Investigation into the Abrasive Waterjet Milling Circular Pocket on Titanium Alloy

Experimental investigation on surface characteristics of Ti6Al4V alloy during abrasive water jet machining process

Modeling and optimization of operating parameters for abrasive waterjet turning alumina ceramics using response surface methodology combined with Box–Behnken design

Evaluation of the Depth and Width of Cuts after Controlled-Depth Abrasive Water Jet Machining Using Low Pressure

Experimental and simulation study on the influence factors of abrasive water jet machining ductile materials

Study on the Effect of Standoff Distance on Processing Performance of Alumina Ceramics in Two Modes of Abrasive Waterjet Turning Patterns

Material removal mechanisms of ceramics turned by abrasive waterjet (AWJ) using a novel approach

A study of abrasive waterjet characteristics by CFD simulation

A review of the current state of abrasive water-jet turning machining method

Analytical and experimental modelling of the abrasive water jet cutting of ductile materials