Abstract:Laser ultrasound is a widely used tool for industrial quality assurance when a contactless and fast method is required. In this work, we used a laboratory setup based on a confocal Fabry–Perot interferometer to examine weld seam models. The focus was placed on small samples with curved surfaces (small in the sense that the radius of curvature is comparable to the largest ultrasonic wavelength) and on efficient ways to detect the presence and volume of process pores, with the goal to transfer this method to industrial applications. In addition to this experimental method for investigating welds, a numerical method that models the experimental setup was implemented in MATLAB. For this purpose, first the thermal effects of the excitation process were taken into account by solving the thermal diffusion equation with an explicit scheme. Then, the elastodynamic equations were solved using the Elastodynamic Finite Integration Technique, taking into account the stresses induced by the excitation process. The B-Scans generated with this numerical model were compared with experimental B-Scans for simple test cases and good agreement was found. In a next step, the additional structures in the B-Scans resulting from air inclusions were identified and investigated with both methods using flat test specimens at first. Besides the direct echoes, structures from skimming surface waves and multiple reflections were visible. These additional structures are unwanted in defect reconstruction methods like the Synthetic Aperture Focusing Technique (SAFT) as they would lead to artifacts. In samples much larger than the largest ultrasound wavelength, however, these unwanted structures are still negligible in amplitude or can be well separated temporally, but for small samples this is no longer the case. As a result, reconstruction methods based on direct echoes like SAFT are difficult to apply. For many industrial applications, the reconstruction is not decisive at all, but only the knowledge of the total volume of process pores (TVPP). It is shown with both experimental and numerical methods, that this TVPP can be estimated from the variation in the B-Scans from various small weld seam models.

The Research of Models for TKY Tubular Joint Welds in Ultrasonic Phased Array Inspection

Application of Visual Beam Ultrasonic Phased Array in Inspection of Weld in Tubular Node

Modelling And Simulation Of Phased Array Transducers Base On Advanced Ut Techniques

The Research on Automatic Defect Recognition for Phased Array Ultrasonic Inspection of Polyolefin Butt Thermal-Fusion Joint

RESEARCH ON THE BREAKAGE MODE AND ANALYTIC MODEL OF CIRCULAR TUBULAR X-JOINTS

Ultimate Strength of the Circular Tubular X-joints

Ultrasonic signal simulation for thick-walled welds based on ray-tracing algorithm and ultrasonic field calculation

Model Based Reliability Analysis of PA Ultrasonic Testing for Weld of Hydro Turbine Runner

A model-based approach for in-situ automatic defect detection in welds using ultrasonic phased array

Nondestructive Testing of an Aluminum Alloy Welded Joint Based on a Mathematical Model of the Thermal Welding Process and Computer Microtomography

Enhanced sizing for surface cracks in welded tubular joints using ultrasonic phased array and image processing

Adaptive probe position correction for automated complex weld inspection based on structural signal monitoring

Full-Matrix Imaging in Fourier Domain towards Ultrasonic Inspection with Wide-Angle Oblique Incidence for Welded Structures

A New Insight on Phased Array Ultrasound Inspection in MIG/MAG Welding

Ultrasonic Inspection for Welds with Irregular Curvature Geometry Using Flexible Phased Array Probes and Semi-Auto Scanners: A Feasibility Study

Health monitoring of plate structures based on tomography with combination of guided wave transmission and reflection

STUDY ON THE USE OF PHASED ARRAY TECHNOLOGY FOR EXAMINATION OF PIPELINES OF THE WWR-K RECATOR

Application Research on Ultrasonic Phased Array Technology in Weld Seam Inspection

Efficient testing of weld seam models with radii of curvature in the millimeter range using laser ultrasound

Imaging of Ultrasonic SH Wave Inspection of Thick-walled Welds Based on Array Technology

Numerical computation methods of welding deformation and their application in bogie frame for high-speed trains