Abstract:Currently, stress analysis on direct bonded copper (DBC) is mainly based on a model with symmetrical top and bottom copper layers. These analyses provide thermal-mechanical stress-relieving methods at the outer edge of the copper-ceramic interface in DBC. However, these methods are unsuitable to release the concentrated stress at the inner gap edges where the top copper layer is etched into the circuit pattern. The stress-concentrated phenomenon causes initial delamination at the inner gap edge of the top copper-ceramic interface in DBC usage. Hence, this paper analyzed the mechanism of the phenomenon and proposed a bottom pattern design method to solve this problem. Through stress analysis on a simplified DBC model with etched top copper, the phenomenon can be explained by the large composite stress produced by the opposite bending actions of the top and bottom copper-ceramic interface in DBC. To reduce the effect of bending action on the bottom interface, parallel dimple traces are used on the bottom instead of a mirror-copied gap on consideration of thermal resistance and mechanical strength. The parameters of dimple trace were chosen by simulations on stress-strain results under thermal cycling and thermal resistance calculations in a module packaging. FE results show that the bottom dimple trace with a diameter of 0.4mm and a gap of 2mm can adjust the thermal-induced strain behavior of the singularities at the top copper to be even and sacrifices only a 2% thermal resistance rise of the module packaging. A life prediction model based on strain shows that the bottom design can improve the lifetime of the substrate. The thermal cycling test result on sample DBC and thermal resistance measurement on the module packaged by DBC with bottom pattern design verify the FE analysis. This method can be widely used in the packaging design of power modules using stand-alone DBC substrate.

DBC Substrate in Si- and SiC-based Power Electronics Modules: Design, Fabrication and Failure Analysis

Crack Initiation and Propagation Mechanism of Al2O3-DBC Substrate During Thermal Cycling Test

An optimal structural design to improve the reliability of Al 2 O 3 –DBC substrates under thermal cycling

Al-clad Cu Bond Wires for Power Electronics Packaging: Microstructure Evolution, Mechanical Performance, and Molecular Dynamics Simulation of Diffusion Behaviors

Measurement of Heat Dissipation and Thermal-Stability of Power Modules on DBC Substrates with Various Ceramics by SiC Micro-Heater Chip System and Ag Sinter Joining

A Stress-Relieved Method Based on Bottom Pattern Design Considering Thermal and Mechanical Behavior of DBC Substrate

Design, Analysis, Comparison, and Experimental Validation of Insulated Metal Substrates for High-Power Wide-Bandgap Power Modules

Thermomechanical Stress Analysis, Characterization and Optimization for Double-Side Cooled Power Modules with Ceramic Substrate

Degradation Behavior of High Power Semiconductor Modules by Low-Temperature Sintering Technology

Thermal and Reliability Characterization of an Epoxy Resin-Based Double-Side Cooled Power Module

1700 V full-SiC half-bridge power module with low switching loss

Improving Power Cycle Lifetime of SiC Power Modules with Double-Bonded Wire: Experimental and Simulation Analysis

Failure Mechanism and Reliability Research of Solder Layer Tilt in Double-Sided Cooling Power Modules

Degradation in Electrothermal Characteristics and Failure Mechanism of SiC JBS with Different Die Attach Materials under 300°C Power Cycle Stress

Interface-Mechanical and Thermal Characteristics of Ag Sinter Joining on Bare DBA Substrate During Aging, Thermal Shock and 1200 W/cm 2 Power Cycling Tests

Competitive Failures Decoupling and Mechanisms Analysis of SiC MOSFET Module Under Power Cycling Stress

Thermal cycling characterization of an integrated low-inductance GaN eHEMT power module

A Study On Novel Integrated Base Plate (Ibp) Package For Power Electronics Module

Reliability Simulation Analysis of TSV Structure in Silicon Interposer under Temperature Cycling

Analysis of the degradation mechanisms occurring in the topside interconnections of IGBT power devices during power cycling

A High Performance Power Module with >10kV capability to Characterize and Test In Situ SiC Devices at >200°C Ambient