Abstract:Tunnel Boring Machine (TBM) tunnelling in weak rock associated with high overburden is very demanding due to the difficulties in predicting the complex interactions between the rock mass, the tunnel machine, its system components, and the tunnel support during excavation/construction. These factors affect the performance and even the feasibility of a TBM drive (sticking of the cutterhead and jamming of the shield may occur). In this respect, several computational models such as the Convergence–Confinement Method (CCM), axially symmetric model and three-dimensional (3D) simulation have been developed in the literature. Among these models, this paper presents three modelling techniques (i.e., a 3D simulator using the Finite Element Method (FEM), an axisymmetric model using the Finite Difference Method (FDM) and an LDP (Longitudinal Displacement Profile) approach based on the CCM), and applies them to the Headrace Tunnel from the Kishanganga Hydroelectric Project in India. The three approaches are not considered to be alternatives but rather complementary to each other, depending on the real situation. The LDP approach is a simplified analytical method but is still efficient to provide a conceptual framework for evaluating the ground-shield interplay during mechanised excavation. The FDM axisymmetric model represents a powerful tool (i.e., with a large deformation scheme available) for the simulation of ground behaviour and its interaction with the machine components, especially in the case of weak rocks with high deformability. However, when the conditions violate the important assumptions underlying these two approaches, true 3D numerical analyses are necessary, which consider all the TBM components. Finally, the paper highlights the potentials of the 3D simulator to model the basic features (i.e., stepwise conicity of the shield, backfilling layer and anisotropic in-situ stress state) of a shield-driven deep tunnel, which determine the tunnel’s behaviour and its response to TBM advancement. The obtained results show that the 3D nature of the complex interactions and the in-situ state of stress, including the nonlinear behaviour can be better reproduced in a 3D simulation than in the other two methods.

3D Simulation of Mechanised Excavation in Brittle Rock

3D Simulation of TBM Excavation in Brittle Rock Associated with Fault Zones: the Brenner Exploratory Tunnel Case

Instability Mechanism of Shallow Tunnel in Soft Rock Subjected to Surcharge Loads

Study Of Surrounding Rock Damage Induced By Tunnel Boring Machine Driving Tunnel At West Route Of South To North Water Transfer Project

Computational Modelling of the Mechanised Excavation of Deep Tunnels in Weak Rock

Model Design and Application for Excavation Face Stability in Upward Shield Tunneling

Physical Model Study on Brittle Failure of Pressurized Deep Tunnel with Support System

Real-time monitoring of the development of brittle fracture in hard rock tunnels based on physical model test

3D NUMERICAL MODELING OF POSSIBLE FAILURE ZONE WITH UNDERGROUND EXCAVATION

Modeling of the Effect of Excavation Mode on the Extent of the Anisotropic Zone Surrounding Deep Tunnels

Tunnel failure mechanism during loading and unloading processes through physical model testing and DEM simulation

Investigation of Rock Mass Stability Around the Tunnels in an Underground Mine in USA Using Three-Dimensional Numerical Modeling

Model test study on the dynamic failure process of tunnel surrounding rocks in jointed rock mass under explosive load

Collapse mechanism and treatments of a deep tunnel in the weathered granite fault zone

Brittle rock mass failure in deep tunnels: The role of infilled structural plane with varying dip angles

Analysis of TBM parameters during tunnelling in adverse conditions – The case study of the Frejus Safety Tunnel, Western Alps

In-situ and experimental investigations of the failure characteristics of surrounding rock through granites with biotite interlayers in a tunnel

Geomechanical Model Experiment Study on Deformation and Failure Mechanism of the Mountain Tunnel in Layered Jointed Rock Mass

Physical modelling of deformation and failure mechanisms and supporting effects for a deep-buried tunnel in inclined layered strata

Numerical study on the rock breaking mechanism of high-pressure water jet-assisted TBM digging technique based on 2D-DEM modelling

Mechanical Behaviors of Steel Segment Support Structures for TBM-Excavated Coal Mine Tunnels: Experimental and Numerical Study