Abstract:In variable nozzle geometry turbines (VNT), opening of the nozzles is used to control turbine mass flow and expansion ratio, allowing more turbine power to be generated over wider operating conditions. In turbocharged vehicles, the nozzles are 'closed' to provide high boosts for engine and vehicle acceleration and for engine braking assistance. At the both conditions, high nozzle expansion ratios are created , and shockwaves may generate from the nozzles. These shocks reduce turbine efficiency and they can cause high cycle fatigue (HCF) damage to the downstream rotor blades. Design of high expansion ratio radial nozzles is difficult for VNT because transonic flows are very sensitive to small geometry changes, and the large semi-vaneless space created by the nozzles makes the design a tricky business. Shock minimised nozzle designs are therefore often achieved by auto-optimisation technique. While design targets may be achieved, this technique does not offer sufficient insights into how the optimal flow field has been derived, so the same optimisation procedure has to be applied to every new design. In this paper, a new design method that overcomes this problem is proposed. The method first uses a conformal mapping to transfer a radial nozzle from the r-θ plane into the x-y plane. Mapped nozzle displays amplification of supersonic acceleration and diffusion. This is explained by the curvature changes brought about by the mapping, and a link between the shock strength and the flatness of the suction surface of the mapped nozzle is found. The amplification and the link can be utilised to design nozzles with reduced shock loss in the x-y plane first and then mapped back to the r-θ plane. Two nozzles for 6:1 expansion ratio were designed in this way and CFD results show a significant reduction of nozzle loss. The nozzles were also checked for fully open condition and no performance penalty was found.

Aerodynamic Optimization Study for a Radial-Inflow Organic Turbine With High Expansion Ratio

Aerodynamic Optimization of a High-Expansion Ratio Organic Radial-Inflow Turbine

Aerodynamic Design and Off-Design Performance Prediction of Radial-Inflow Turbine With Organic Gas as Working Fluid

Design Optimization of A Small Scale High Expansion Ratio Organic Vapour Turbo Expander for Automotive Application

DESIGN AND FLOW ANALYSIS OF A RADIAL OUTFLOW TURBO-EXPANDER

Aerodynamic Design and Optimization of a Radial Inflow Millimeter-Scale Turbine

An Investigation of the Flow Structure in the Radial Inflow Transonic Turbine

Optimization Design of Aspect Ratio and Solidity of a Heavy-Duty Gas Turbine Transonic Compressor Rotor

Performance Analysis of Low Speed Axial Impulse Turbine Using Two Type Nozzles for Small-Scale Organic Rankine Cycle

Numerical study of organic Rankine cycle radialinflow turbines for heavy‐duty diesel engine coolant heat recovery

Study on Aerodynamic Performance and Optimization Design of a Turbine in Liquid Rocket Engine

Similarity Theory Based Radial Turbine Performance and Loss Mechanism Comparison Between R245fa and Air for Heavy-Duty Diesel Engine Organic Rankine Cycles

Experimental And Numerical Investigation On Overall Performance Of A Radial Inflow Turbine For 100kw Microturbine

A novel design method of variable geometry turbine nozzles for high expansion ratios

Optimal Design and Tip Leakage Flow Characteristics Analysis of Radial Inflow Turbine Used in Organic Rankine and Vapor Compression Refrigeration System

Study On The Steady And Unsteady Aerodynamic Performance Of A Radial Inflow Turbine With Small Partial Admission In A Miniature Orc System

Preliminary Design Of Multistage Radial Turbines Based On Rotor Loss Characteristics Under Variable Operating Conditions

Aerodynamic and Performance Behavior of A Radial Turbine at Design and Off-Design Conditions

Investigation of the Organic Rankine Cycle (ORC) System and the Radial-Inflow Turbine Design

Numerical Study on Nozzle Exit Flow Angle for Radial Turbine

Meridional Shape Optimization of Radial Inflow Turbine Impeller