Abstract:Bismuth ferrite nano‐ and microcrystals were prepared by a facile molten salt technique in two kinds of molten‐salt‐based systems (NaCl–KCl and NaCl–Na2SO4). In the NaCl–KCl salt system, a systematic study indicating the effects of process parameters (e.g., calcination temperature, holding time as well as the molten salt ratios) on the bismuth ferrite formation mechanism and structural characteristics is reported. The results show that almost pure phase BiFeO3 powders with minimum impurity phase of Bi2Fe4O9 were synthesized at temperatures of 700°C–800°C, whereas high calcination temperature (e.g., 900°C) resulted in the formation of almost pure phase Bi2Fe4O9 powders. The prolonged holding time increased the particle size via the Ostwald ripening mechanism; however, there was little effect on the particle morphology. Similar phenomenon occurred as increasing the molten salt ratios. In the NaCl–Na2SO4 salt systems, it is found that low NP‐9 (nonylphenyl ether, NP‐9) surfactant content (0–5 mL) led to the formation of almost pure phase BiFeO3 powders, whereas high NP‐9 surfactant content (e.g., 20 mL) resulted in pure phase Bi2Fe4O9 powders. The average particle size of the BiFeO3 powders was decreased as increasing the NP‐9 surfactant content, whereas their morphologies did not change significantly. Because of the simplicity and versatility of the approach used, it is expected that this methodology can be generalized to the large‐scale preparation of other important transitional metal oxides with controllable sizes and shapes.

Molten salt synthesis of Bi2SiO5 powders based on uniform experiment

Synthesis of Pure Bi<sub>12</sub>SiO<sub>20</sub> Powder by Molten Salt Method

Effects of Process Parameters on Bi4 Si3 O12 Powders Synthesized by Molten Salt Method

Molten-salt Synthesis of BaTiO3 Powders and Their Atomic-Scale Structural Characterization

Molten Salt Synthesis of Bismuth Ferrite Nano‐ and Microcrystals and Their Structural Characterization

Study of the synthetic process of CaBi2Ta2O9 powder by the molten‐salt method

Molten Salt Synthesis of ZnNb{sub 2}o{sub 6} Powder

The Effect of Solution Treatment on the Si Particles’ Morphology Evolution and the Thermal Conductivity and Tensile Properties of Sb-Modified Al-8Si-0.6Mg Alloys

Effect of poly sodium-p-styrenesulfonate on the phase formation and morphology of the hydrothermally synthesized bismuth ferrite powders

Synthesis of compounds with a crystal structure of sillenite within the pseudobinary stable system Bi12GeO20–Bi12SiO20*

New Insights into the Synthesis of Sillén–Aurivillius Oxyhalides: Molten Salt induces Interlayer Halogen Competing Reaction

Thermal decomposition of bismuth oxysulfide from photoelectric Bi2O2S to superconducting Bi4O4S3

Microstructures and properties of (65-x)SiO2-xBi2O3-10B2O3-25CuO glasses

Mechanism study of Sr1-xBaxBi4Ti4O15 ferroelectrics materials fabricated by sol-gel process

Synthesis, microstructural characterization, and dielectric properties of BiFeO3 microcrystals derived from molten salt method

Hydrothermal synthesis and characterization of Bi4Ti 3O12 powders

Hydrothermal preparation and characterization of rod-like ultrafine powders of bismuth sulfide

Effect of synthesis method upon the dielectric properties of SrBi2Ta2O9

Synthesis and Characterization of Sr1−xBaxBi4Ti4O15 Ferroelectric Materials

Structural evolution and synthesis mechanism of ytterbium disilicate powders prepared by cocurrent chemical coprecipitation method

Effect of solid-state reaction synthesis temperature of SrBi 2Ta2O9 on its sintering behavior