Abstract:In this work, the stability behaviors of the state-of-the-art Fe/N/C and Pt/C catalysts (as well as the activation time of the latter) were first systematically investigated, under different cathode catalyst loadings, in the membrane electrode assemblies (MEA) in PEM fuel cells. Based on that, two types of cathode electrodes with the combination of Fe/N/C and Pt/C catalysts were developed (type I: layered hybrid catalysts with Pt/C next to the membrane and type II: uniformly mixed catalysts). In this way, the shortcomings of the Fe/N/C catalyst (the fast decay) and the Pt/C catalyst (the long activation time) can be compensated at the same time. The hybrid catalysts also showed a very short activation time (a few hours vs over 10 h for Pt/C with the same Pt loading). Comparing the two types of hybrid catalysts, type I shows a much higher current density. The loadings of the Fe/N/C and Pt/C catalysts in the hybrid electrode were systematically studied, with optimal values of 1.0 mg cm(-2) for Fe/N/C and 0.035 mg(Pt) cm(-2) for Pt/C. The Pt loading of this hybrid catalyst (type I) at the cathode only takes ca. 30% of the U.S. Department of Energy (DOE) target of Pt usage (0.100 mg(Pt) cm(-2)), while its mass activity of Pt (in H-2/O-2 PEMFC) is 0.22 A mg(Pt)(-1) at 0.9(iR-free) V, reaching half of the DOE activity target (0.44 A mg(Pt)(-1)), which is among the best performances reported so far. Via both half-cell and single-cell electrochemical evaluations together with other characterizations, the origin of the improved activity and stability is believed to be the synergistic effect between Pt/C and Fe/N/C catalysts to ORR. This work provides an effective strategy for engineering highly performing MEA for the industrialization of PEM fuel cells.

Electrode structure optimization combined with water feeding modes for Bi-Functional Unitized Regenerative Fuel Cells

Polymer electrolyte membrane unitized regenerative fuel cells: Operational considerations for achieving high round trip efficiency at low catalyst loading

A novel cooperative design with optimized flow field on bipolar plates and hybrid wettability gas diffusion layer for proton exchange membrane unitized regenerative fuel cell

Efficient Drainage Design of Cathode Catalyst Layer for Pure Oxygen Proton Exchange Membrane Fuel Cells

High-performance AEM unitized regenerative fuel cell using Pt-pyrochlore as bifunctional oxygen electrocatalyst

The Performance Improvement of Membrane and Electrode Assembly in Open-Cathode Proton Exchange Membrane Fuel Cell

Strategies for Improving Anion Exchange Membrane Fuel Cell Performance by Optimizing Electrode Conditions

New electrocatalysts for unitized regenerative fuel cell: Pt-Ir alloy deposited on the proton exchange membrane surface by impregnation-reduction method

Ultrahigh PEMFC performance of a thin-film, dual-electrode assembly with tailored electrode morphology

Effective single web-structured electrode for high membrane electrode assembly performance in polymer electrolyte membrane fuel cell

High-Performance Hydroxide Exchange Membrane Fuel Cells Through Optimization of Relative Humidity, Backpressure and Catalyst Selection

Water-gas two-phase transport behavior and purge strategy optimization during mode-switching of unitized regenerative proton exchange membrane fuel cell

Design and multi-objective optimization of low-temperature proton exchange membrane fuel cells with efficient water recovery and high electrochemical performance

A Novel Self-Humidifying Membrane Electrode Assembly with Water Transfer Region for Proton Exchange Membrane Fuel Cells

Optimizing proton exchange membrane fuel cell performance at low-humidity via constructing additional anodic water-retaining membrane layer containing sulfonated multi-walled carbon nanotubes

Mass Transfer and Round-Trip Efficiency Evaluation of Unitized Regeneration Proton Exchange Membrane Fuel Cell During Bi-Directional Mode Switching Cycle

Design of graded cathode catalyst layers with various ionomers for fuel cell application

Hierarchical mesh-type oxygen electrode using carbon nanotube framework for anion-exchange membrane-based unitized regenerative fuel cells

Improving the High-Current-Density Performance of PEMFC Through Much Enhanced Utilization of Platinum Electrocatalysts on Carbon

PGM-Free Fe/N/C and Ultralow Loading Pt/C Hybrid Cathode Catalysts with Enhanced Stability and Activity in PEM Fuel Cells

Enhanced Water Management in the Cathode of an Air-Breathing PEMFC Using a Dual Catalyst Layer and Optimizing the Gas Diffusion and Microporous Layers