Abstract:Aims: This study aims to propose an 8-bit differential input low-power Successi,e Approximation Register (SAR) ADC with digital error correction technique for sensing bio-potential signals in wearable and implantable devices. Background: As dynamic comparators have the advantages of full swing output, low power consumption, high speed, and high impedance at the input, they are preferably used in energy-efficient SAR ADC’s. However, since the dynamic comparator is the most frequently used block in SAR ADC, research is ongoing to reduce its μW power further. Also, as the offset voltage of the comparator affects the linearity of ADC, it must be minimized. Linearity can further be improved by calibrating the output of ADC, and extensive surveys on the calibration methods prove that the addition- only digital error correction method is efficient in terms of power. Objective: The objective of this study is to design a low-power and low-offset dynamic comparator intended for SAR ADC to achieve highly linear digital output. In addition to this, the objective is to implement a power-efficient digital error correction technique for the output of SAR ADC to overcome the non-idealities due to process variations. Method: As power consumption is proportional to the number of transistors, the proposed comparator is a design obtaining the same output as the existing dynamic comparators with reduced transistor count. The proposed comparator, along with low power full swing three-input XOR logic gate, is implemented in SAR ADC with digital error correction technique in cadence 45 nm technology files, and its performance parameters are simulated. Results: The layout of the proposed dynamic comparator occupies an area of 3 μm 2 . The simulation results of this comparator with a load of 1 pF show that it has a total offset of 11.2 mV, a delay of 0.9 ns, and power consumption of 24 nW. It also achieves a gain of 49.5, i.e., 33.86 dB. The 8-bit ADC, along with the digital error correction technique operating at 143-kS/s and under 0.6 V supply voltage simulated in 45nm technology, consumes only 0.12 μW of power. The DNL and INL errors obtained are +0.22/-0.2 LSB and -0.28 LSB, respectively. SNR limited by noise is 48.25 dB, SFDR is 48.64 dB, and ENOB achieved is 7.72. Conclusion: To satisfy the requirement of the wearable and implantable devices, a low-power SAR ADC with good linearity is designed using a low-power and low-offset dynamic comparator. A digital error correction technique using a low-power XOR logic gate is implemented at the SAR ADC output to minimize the non-idealities due to the process variations.

A 10-bit low-power differential successive approximation ADC for implantable biomedical application

A 10-Bit 250-KS/s 1.24-uW SAR ADC for IoT Sensors with Energy-Efficient Comparator.

A 5.8 nW 9.1-ENOB 1-kS/s Local Asynchronous Successive Approximation Register ADC for Implantable Medical Device

Low Voltage Low Power SAR ADC for Implantable Medical Chips

A 0.3V 10b 3MS/s SAR ADC With Comparator Calibration and Kickback Noise Reduction for Biomedical Applications

A 0.6-V 10-bit 200-kS/s Fully Differential SAR ADC With Incremental Converting Algorithm for Energy Efficient Applications

An 8-Bit 100ks/s Low Power Successive Approximation Register ADC for Biomedical Applications

Design of a 0.2V 2.08nW 10-bit 1kS/s High Energy Efficiency SAR ADC with Dummy Capacitor Splitting Technique for Biomedical Applications

A 0.9V 12-Bit 200-Ks/s 1.07µw SAR ADC with Ladder-Based Reconfigurable Time-Domain Comparator

A Low Power Cyclic ADC Design for a Wireless Monitoring System for Orthopedic Implants

A 150 MS/s 10-Bit CMOS Pipelined Subranging ADC with Time Constant Reduction Technique.

A Study Of A10-Bit 50ms/S Low Voltage Low Power Pipelined Adc

A 10-bit 1kS/s-30kS/s successive approximation register analog-to-digital converter for biological signal acquisition

A Low Power SAR ADC with Digital Error Correction Technique for Wearable and Implantable ECG Devices

A Low Voltage and Low Power 10-Bit Non-Binary 2b/cycle Time and Voltage Based SAR ADC

A Low Power 12-Bit 200-Ks/s SAR ADC with a Differential Time Domain Comparator

A 10-Bit 16-Ms/s Ultra Low Power SAR ADC for IoT Applications

A 8.9-ENOB 2.5-εW 150-KS/s non-binary redundant successive approximation ADC in 0.18-μm CMOS for bio-implanted devices

Design of an Ultra-Low Power SAR ADC for Biomedical Applications

An ultra low power 10-bit 1KS SAR-ADC for ECG signal recording applications

An Ultra Low Power 9-Bit 1-Ms/s Pipelined SAR ADC for Bio-Medical Applications