Abstract:Flow chart for the preparation of PEN‐based composite films. Thermal conductive polymer‐based composites synchronously with stable dielectric and excellent mechanical properties are urgently needed for high‐temperature‐resistant electronic devices. Here, a significant improvement in the thermal conductivity (TC), thermal stability, dielectric, and mechanical performance was simultaneously achieved in the polyarylene ether nitrile (PEN)/divinyl siloxane‐bisbenzocyclobutene (BCB) matrix through the incorporation of boron nitride nanosheets (BNNS) combined together with the post‐solid phase chemical reaction technique. The significant increase in the effective filler‐filler and filler‐crystal contacts in the composites was the main reason for the improvement in TC and dielectric constant. Besides, glass transition temperature (Tg) and mechanicals were enhanced in the presence of cross‐linked networks. By synchronously adding 15 vol% BNNS, the TC of composites after treatment reached up to 5.582 W/m.K, enhanced by 4.4 times higher than untreated. The dielectric constant was down to 2.93 at 1 MHz and the loss remained at a relatively low level. Meanwhile, the composite showed significantly enhanced thermal stability, mechanicals, and hydrophobicity (Tg = 336°C, T5% = 529°C, tensile strength and modulus was 94.5 MPa and 5.3 GPa, respectively, the contact angle was 101.76°). Thus, it promotes an effective strategy for fabricating a high‐performance‐polymer composite, which has the potential used in electronic materials. Highlights Crystallization‐crosslinking strategy optimizes overall performance. Crystals fill gaps between BNNS layers and connect thermal conductive pathway. Crosslinked networks limit molecular chain motion to reduce phonon scattering. The highest TC of the PEN/BCB/BNNS composite is up to 7.451 W/m.K. Thermal property shows significant improvement after crosslinking especially Tg.

Mechanical, thermal, electrical, and interfacial properties of high-performance bisphthalonitrile/polyarylene ether nitrile/glass fiber composite laminates

Properties of the Glass Fibre/interpenetrating Polymer Network Composites Based on Novel Naphthalene-Contained Bismaleimide and Cyanate Resin

Cure of Neat Resins and Properties of Composites for Interpenetrating Polymer Networks from the Novel Bismaleimide and Cyanate Containing Naphthalene

Preparation And Properties Of Bisphenol A-Based Bis-Phthalonitrile Composite Laminates

Manufacturing and thermal and mechanical properties of advanced 3-aminophenoxyphthalonitrile/bisphthalonitrile composite laminates

Design of the Phthalonitrile-Based Composite Laminates by Improving the Interfacial Compatibility and Their Enhanced Properties

Advanced Composites Based on End-Capped Polyarylene Ether Nitrile/bisphthalonitrile with Controllable Thermal Curing Reaction

Effect of polyarylene ether nitriles on processing and mechanical behaviors of phthalonitrile-epoxy copolymers and glass fiber laminated composites

Designing and Preparation of Fiber-Reinforced Composites with Enhanced Interface Adhesion

Effect of Polyarylene Ether Nitrile on the Curing Behaviors and Properties of Bisphthalonitrile

Synthesis and characterization of cyano-terminated bisphenol AF-type polyarylene ether nitrile

Modification on Glass Fiber Surface and Their Improved Properties of Fiber-Reinforced Composites Via Enhanced Interfacial Properties

Curing Behavior And Processability Of Bmi/3-Apn System For Advanced Glass Fiber Composite Laminates

Branched Fluorine/Adamantane Interfacial Compatibilizer for PBO Fibers/Cyanate Ester Wave-Transparent Laminated Composites

Polyarylene ether nitrile/divinyl siloxane‐bisbenzocyclobutene composite films: Curing reaction and thermal/mechanical/dielectric properties

Substantial improvement of thermal conductivity and mechanical properties of polymer composites by incorporation of boron nitride nanosheets and modulation of thermal curing reaction

Mechanical and Thermal Properties of Graphite Nanoplatelets Reinforced Polyarylene Ether Nitriles/Bisphthalonitrile Ipn System

Improved mechanical properties of basalt fiber/phthalonitrile composites modified by thermoplastic Poly(phthalazinone ether nitrile)s

Toughening Effect of Self-Assembled Thermoplastic Particles on Phthalonitrile Containing Benzoxazine and Improved Mechanical Properties in the Presence of Fibers Reinforcement

Design of Low Temperature Self-Cured Phthalonitrile-Based Polymers for Advanced Glass Fiber Composite Laminates

Curing behaviors and performance of a carboxyl-terminated butadiene acrylonitrile rubber/bisphthalonitrile resin system