Abstract:Since Li-oxygen (Li-O2) battery was first roported in 1996 by Abraham and Jiang 1, it had been attracting increasingly attention due to its remarkably high theoretical specific energy of 11400 Wh/kg, which is very close to that of gasoline (13000 Wh/kg) and is regarded as the most promising alternative to fossil fuel based energy2. However, the practical capacity of Li-O2 battery is always far below the theoretical value. The prime reason is that, up discharging, the insoluble discharge product, namely Li2O2, will block the paths for both oxygen and the electrolyte and result in an early termination of the discharge process. So the specific capacity of Li-O2 electrode strongly depends on the porosity of the electrode. And it is very crucial to build porous air electrodes with plenty of voids to accommodate Li2O2 and to facilitate the transportation of oxygen and electrolyte. Up to now, various mesoporous materials or nano-structured materials have been explored to make porous electrodes for Li-O2batteries and have promoted the electrochemical performance significantly. However, present electrode manufacturing prefer to use polyvinyliden-di-fluoride (PVdF) as the binder and use volatile organic solvents such as N-methyl-pyrrolidone (NMP). Most of these solvents cost a lot and lead to the harmful environment pollution during the electrode manufacturing process. In addition, PVdF is also a relatively costly polymer and is necessary to be substitued by an economic binder. Herein, we proposed a green method to build a porous air electrode for Li-O2 batteries by a freeze-dry process with carboxymethyl cellulose (CMC) as the binder. The electrode is characterized with abundant voids for discharge product, which also provide plenty of effective passages for both oxygen and electrolyte. This electrode demonstrate not only a high specific capacity but also an excellent rechargeable ability by combination with high conductive MWCNT. As shown in Figure 1a, at a current density of 100 mA g-1, the porous air cathode demonstrates an initial discharge capacity of 6,702 mAh g-1 with an average discharge potential of about 2.70 V. The increased discharge capacity can be ascribed to the fact that the plenty of room in the porous electrode accommodate more discharge product. Meanwhile, the abundant space facilitates the transportation of oxygen and electrolyte, thus extending the discharge process. The high conductivity of MWCNT also promotes the electrochemical performance of Li-O2batteries. By all the virtues above, the porous air cathode shows an enhanced cycling life as high as 53cycles (Figure 1b). Acknowledgement This work was supported by Science Foundation of Ministry of Education of China (grant 413064), the Program for Professor of Special Appointment (Eastern Scholar) at Shanghai Institutions of Higher Learning. Reference 1. K. M. Abraham, J. Electrochem. Soc. 1996, 143, 1-5. 2. Z. Q. Peng, S. A. Freunberger, Y. H. Chen, P. G. Bruce, Science, 2012, 337, 563 – 566. Figure 1

A High-Capacity Lithium–air Battery with Pd Modified Carbon Nanotube Sponge Cathode Working in Regular Air

Unprecedented Strong and Reversible Atomic Orbital Hybridization Enables a Highly Stable Li-S Battery

Compressible, gradient-immersion, regenerable carbon nanotube sponges as high-performance lithium–oxygen battery cathodes

Mesoporous Co3O4 -Rods-Entangled Carbonized Polyaniline Nanotubes as an Efficient Cathode Material toward Stable Lithium-Air Batteries

Self-Catalyzed Growth of Co4N and N-Doped Carbon Nanotubes toward Bifunctional Cathode for Highly Safe and Flexible Li-Air Batteries

Porous sulfurized poly(acrylonitrile) nanofiber as a long-life and high-capacity cathode for lithium–sulfur batteries

A Carbon Powder-Nanotube Composite Cathode for Non-Aqueous Lithium-Air Batteries

Fabrication and Performance of All-Solid-State Li-Air Battery with SWCNTs/LAGP Cathode.

Carbon Nanofiber-Based Sandwich Free-Standing Cathode for High-Performance Lithium-Sulfur Batteries

Air‐Stable Li2S Cathode for Quasi‐Solid‐State Anode‐Free Batteries with High Volumetric Energy

Preparation of high-capacity air electrode for lithium-air batteries

A High-Performance Solid-State Lithium-Oxygen Battery with A Ceramic-Carbon Nanostructured Electrode

A Porous Air Electrode for Li-O2 Batteries Based on a Green Method

An Air‐Stable High‐Nickel Cathode with Reinforced Electrochemical Performance Enabled by Convertible Amorphous Li 2 CO 3 Modification

Cathode Catalysts and Process for Rechargeable Li-air Batteries

Coupling Water‐Proof Li Anodes with LiOH‐Based Cathodes Enables Highly Rechargeable Lithium–Air Batteries Operating in Ambient Air

Pencil-drawing on Nitrogen and Sulfur Co-Doped Carbon Paper: an Effective and Stable Host to Pre-Store Li for High-Performance Lithium–air Batteries

A High‐Performance Lithium Metal Battery with Ion‐Selective Nanofluidic Transport in a Conjugated Microporous Polymer Protective Layer

Facile Synthesis of Cobalt-Copper Layered Double Hydroxide Nanosheets As Cathode Catalysts for Rechargeable Lithium-Air Batteries

A Novel Air Electrode Design: A Key to High Rate Capability and Long Life Span

High Areal Capacity, Long Cycle Life Li–Air Batteries Enabled by Nano/Micro Hierarchical Porous Cathode