Abstract:Introduction The lithium-air batteries have attracted much more attentions because of its high theoretical energy density, which is over 3500 Wh kg-1. However the lithium-air batteries still have a lot of problems and the problem related with the decomposition of organic liquid electrolytes is the most serious and one of the main research topics in the present stage. Thus, we have developed all-solid-state lithium-air batteries using the inorganic solid electrolytes, which are more stable than the liquid electrolytes. The application of the solid electrolytes to the lithium-air batteries can solve not only the decomposition of electrolytes but also the safety problem and some other problems specific to the liquid such as leakage and volatilization. In this study, all-solid-state cells consisting of Li anode, Li1+xAlyGe2-y(PO4)3 (LAGP) solid electrolyte, and LAGP-carbon nanotube (CNT) composite cathode was operated in the air atmosphere (so-called Li-air cell) and pure oxygen atmosphere (so-called Li-O2 cell). Reaction mechanism during discharge-and charge was investigated. Experiments The Li / LAGP / LAGP-CNT cells were assembled by the following procedure. LAGP powders and pellets were prepared by the conventional solid-state method. CNT and LAGP powders were dispersed into the ethanol solution. A drop of the solution was put on the LAGP pellet and dried at room temperature. The air electrode deposited on the LAGP pellet was heated at 700 oC. After sintering, the air electrode combined with the solid electrolyte layer was obtained. On the other side of the LAGP pellet, a Li anode was contacted with the LAGP pellet by a thermal adhesion process and sealed with a plastic film. An Al mesh and a Cu mesh were used as a current collector for the cathode and the anode, respectively. The laminate-type cell was sandwiched by two plastic plates and held by a screw clamp. The Li-air cell was operated in the laboratory air atmosphere. The Li-O2 cell was put into the bottle connecting to the oxygen gas flow channel, and discharged and charged under a pure oxygen gas-flowing condition. Results and discussion The all-solid-state cells were discharged and charged by the constant current mode in the voltage range of 2.0 - 4.8 V. The Li-O2 cell showed a discharge plateau at 2.0 - 2.5 V and, the charge plateau gradually increased from 3.0 to 4.2 V. On the other hand, the Li-air cell showed a discharge plateau, which starts 3.0 V at a low current density, and the charge curve obviously showed two plateaus. In such cells, the air electrode after discharging and charging was analyzed by using XRD, XPS, Raman, IR, and TEM. From these measurements, it was suggested that Li2O2 was electrochemically produced after discharging in both air and oxygen atmosphere. Also Li2CO3 was produced by side-reactions. The reaction products in air atmosphere were the same as that in oxygen atmosphere. However, the elementary process seems to be different between air and oxygen. It was also found that the CNT was degraded during cycling, which would cause the capacity degradation.

Fabrication and Performance of All-Solid-State Li-Air Battery with SWCNTs/LAGP Cathode.

LiNi0.5Mn1.5O4 cathode microstructure for all-solid-state batteries

A Design of Solid-State Li-S Cell with Evaporated Lithium Anode to Eliminate Shuttle Effects.

Intensive Investigation on All-Solid-state Li-air Batteries with Cathode Catalysts of Single-Walled Carbon Nanotube/ruo2

Electrochemical Performance of Solid‐State Lithium–Air Batteries Using Carbon Nanotube Catalyst in the Air Electrode

Electrochemical Performance and Reaction Mechanism of All-Solid-state Lithium–air Batteries Composed of Lithium, Li1+xAlyGe2−y(PO4)3 Solid Electrolyte and Carbon Nanotube Air Electrode

Mesoporous Co3O4 -Rods-Entangled Carbonized Polyaniline Nanotubes as an Efficient Cathode Material toward Stable Lithium-Air Batteries

CNTs@S Composite As Cathode for All-Solid-state Lithium-Sulfur Batteries with Ultralong Cycle Life

Boosting the Rate Performance and Capacity of Sb2S3 Nanorods Cathode by Carbon Coating in All‐Solid‐State Lithium Batteries

A High-Capacity Lithium–air Battery with Pd Modified Carbon Nanotube Sponge Cathode Working in Regular Air

Composite Cathodes Containing SWCNT@S Coaxial Nanocables: Facile Synthesis, Surface Modification, and Enhanced Performance for Li‐Ion Storage

High-Performance Cathodes Prepared Via Liquid-Phase Method and Catalyzed by Co9S8 for All-Solid-State Lithium-Sulfur Batteries

Interface Engineering of a NASICON-Type Electrolyte Using Ultrathin CuS Film for Lithium Metal Batteries

Surface-modified and sulfide electrolyte-infiltrated LiNi0.6Co0.2Mn0.2O2 cathode for all-solid-state lithium batteries

Lithium Argyrodite as Solid Electrolyte and Cathode Precursor for Solid‐State Batteries with Long Cycle Life

Rational Design of an Electron/Ion Dual-Conductive Cathode Framework for High-Performance All-Solid-State Lithium Batteries.

Sandwich structured NASICON-type electrolyte matched with sulfurized polyacrylonitrile cathode for high performance solid-state lithium-sulfur batteries

Investigation of Reaction Mechanism in All-Solid-State Li-Air and Li-O<sub>2</sub> Batteries

<i>In Situ</i> Coating of Li<sub>7</sub>P<sub>3</sub>S<sub>11</sub> Electrolyte on CuCo<sub>2</sub>S<sub>4</sub>/Graphene Nanocomposite as a High-Performance Cathode for All-Solid-State Lithium Batteries

Ultrasmall Li 2 S-Carbon Nanotube Nanocomposites for High-Rate All-Solid-State Lithium–Sulfur Batteries

Pencil-drawing on Nitrogen and Sulfur Co-Doped Carbon Paper: an Effective and Stable Host to Pre-Store Li for High-Performance Lithium–air Batteries