Abstract:HA composite coatings added reinforcement phases could improve the mechanical properties and bonding strength of the coatings. Cold spraying is a feasible surface technology for preparing HA composite coatings. In order to investigate the influence of cold spraying parameters on the deposition behavior of a single HA/Ti composite particle, numerical and experimental investigation of gas-particle two-phase flow in cold spraying nanostructured HA/Ti composite particle were investigated in this study. The results show that the influence of different temperatures and pressures on static pressure was not significant. The effects of gas pressure on the static temperature were tiny under the same inlet temperature and different pressure conditions; however, the static temperature in the entire spray gun cavity increased as the inlet temperature increased under the same pressure and different inlet temperature conditions. There is little effect of gas pressure on the axial velocity of gas flow in the spray gun cavity; however, the axial velocity of gas flow increased with the increase in gas temperature. Meanwhile, the axial velocity of gas flow gradually increases throughout the spraying process. At a gas temperature of 573 K and 973 K, the maximum axial velocities of a gas flow at gas pressure of 2.2 MPa were 778 m/s and 942 m/s, respectively. There is little effect of gas pressure on the axial velocity of HA/30 wt.% Ti particles under the same gas temperature. The axial velocity of HA/30 wt.% Ti particles increased with the increase in gas temperature under the same gas pressure condition. The axial velocity of composite particles decreased with the increase in the particle size under the same gas pressure and gas temperature. At a gas temperature of 573 K and 973 K, the minimum axial velocity of HA/30 wt.% Ti particles with a particle size of 30 μm at a gas pressure of 2.2 MPa was 435 m/s and 467 m/s, respectively. A certain deformation of splats occurred after impacting the substrate, and the splats adhered to the surface of the Ti6Al4Vsubstrate, clearly presenting a flat shape with a central hump surrounded by a ringy band. At a gas temperature of 973 K, particles generated more severe deformation with more cracks and ejecta phenomenon. The splats attached to the substrate were increased as the gas temperature increased.

Numerical Study on the Effect of Nozzle Dimension on Particle Distribution in Cold Spraying

3D analysis of gas flow behavior and particle acceleration characteristics in cold spray additive manufacturing based on non-axisymmetric numerical models

Study on the Atomization Characteristics of High-pressure Nozzle with an In-line Distributor

Research on structure and technological parameters of multi-channel cold spraying nozzle

Numerical Study of Powder Particle Flight Behavior during Gas Detonation Spraying Process

Dynamic Modeling of Micro- and Nano-Sized Particles Impinging on the Substrate During Suspension Plasma Spraying

Effects of Atomization Injection on Nanoparticle Processing in Suspension Plasma Spray

Modeling of Micro- and Nanoparticle Characteristics in DC Suspension Plasma Spray

Research Progress on Numerical Simulation of the Deposition and Deformation Behavior of Cold Spray Particles

Effects of operating conditions on droplet deposition onto surface of atomization impinging spray

Effect of Spray Distance and Powder Feed Rate on Particle Velocity in Cold Spray Processes

Nanoparticles Modeling in Axially Injection Suspension Plasma Spray of Zirconia and Alumina Ceramics

Generic Correlation Of Spray Distance With In-Flight Particle Behavior For Different Kinds Of Materials In Air Plasma Spraying

Study of Injection Angle and Carrier Gas Flow Rate Effects on Particles In-Flight Characteristics in Plasma Spray Process: Modeling and Experiments

Numerical and Experimental Investigation Gas-Particle Two Phase Flow in Cold Spraying Nanostructured HA/Ti Composite Particle

Numerical and experimental study of the effects of tangential to axial velocity ratio and structural parameters inside the nozzle on spray characteristics

Prediction of deformation characteristics and critical velocities during cold-spray: A new 3D model

The effect of particle size on aluminum dust dispersion based on numerical simulation

Effect of Injection Angle on Particles In-Flight Characteristics

Numerical Simulations of Molten Breakup Behaviors of a de Laval-Type Nozzle, and the Effects of Atomization Parameters on Particle Size Distribution

Three-dimensional simulation of plasma spray: effects of carrier gas flow and particle injection on plasma jet and entrained particle behavior