Abstract:Two fluorescent high‐performance polymers based on dicyanoarylamine luminogens were readily synthesized via polycondensation. Both polymers were soluble in several polar aprotic solvents and exhibited useful levels of thermal stability. The polymers were emissive in both solution and solid film states, thereby demonstrating the aggregation‐induced fluorescence changes. Introduction Fluorescent high‐performance polymers have been extensively used in designing optoelectronic devices due to their low cost, excellent thermal stability, high mechanical strength, low flammability, good chemical and radiation resistance, and good electronic properties. While conventional organic luminophores fluoresce strongly in dilute solutions, they suffer from undesirable aggregation‐caused quenching in concentrated solutions and in the solid state due to extensive π‐π stacking interactions and formation of delocalized excitons or excimers. This phenomenon leads to non‐radiative decay thus, decreased fluorescence emission of the material in the solid film state, which significantly limits their real‐world application as solid light‐emitting materials. Objectives To develop new high‐performance polymers with high photo luminescent efficiency, good processability, film‐forming properties, which could potentially be used in the fabrication of optoelectronic devices. Methods The preparation of the polyimide DiCN‐PI was carried out by a one‐step, high‐temperature solution imidization method. In this procedure, 1,2,4,5‐cyclohexanetetracarboxylic dianhydride and the diamine were polymerized in 1‐methyl‐2‐pyrrolidinone and γ‐butyrolactone co‐solvent at 180°C for 15 hours in the presence of isoquinoline as catalyst. On the other hand, polyamide DiCN‐PA was synthesized according to the direct phosphorylation polycondensation technique described by Yamazaki from diamine and trans‐1,4‐cyclohexanedicarboxylic acid using triphenyl phosphite and pyridine as condensing agents. Results and Discussion Both polymers were soluble in several polar aprotic solvents and exhibited useful levels of thermal stability. The polymers were emissive with PL emission bands around 555 (bluish‐green) and 498 (cyan) nm in dilute 1‐methyl‐2‐pyrrolidinone solutions for polyimide and polyamide, respectively. In the solid film state, the polymers emit light green and yellow colors, which simulate the PL behavior of their aggregated states, thereby demonstrating aggregation‐induced fluorescence changes. Conclusions These results indicate that the incorporation of bulky dicyanoarylamine moiety and alicyclic monomer units into the rigid polymer backbones effectively disrupted the planarity of the chain packing which resulted to the fluorescent high‐performance polymers with desired properties for potential optoelectronic applications.

Synthesis and Characterization of N‐methyl‐2,6‐dinitrodiphenylamine‐4‐diazonium Salt and Its Diazoresin

Dicarbazolyldicyanobenzenes as Thermally Activated Delayed Fluorescence Emitters: Effect of Substitution Position on Photoluminescent and Electroluminescent Properties

Syntheses and Properties of 3-Methoxy-diphenylamine-4-diazonium Salts and Their Diazo Resins

Synthesis, characterization and self-promoted cure behaviors of a new phthalonitrile derivative 4-(4-(3, 5-diaminobenzoyl) phenoxy) phthalonitrile

Synthesis and Properties of a Polymerizable Quaternary Ammonium Salt

Synthesis and Spectral Characterization of a Novel Fluorescent Functional Monomer 2,4-Dimethyl-7-acrylamine-1,8-naphthyridine

Syntheses of Novel 1,3-Diazaazulene Derivatives and Their Nonlinear Optical Characterization

Synthesis and Characterization of Novel Reactive 1,8-Naphthalimide-based Fluorescent Molecules

Preparation of Photosensitive Polymeric Microspheres Via Soap-Free Emulsion Polymerization and Its Photo-Responsivity

A NOVEL CHEMICAL AMPLIFICATION TYPE POSITIVE RESIST USING DIPHENYLIODONIUM 9, 10-DIMETHOXYANTHRACENE-2-SULPHONATE AS PHOTOINITIATOR

A Novel Multi-Purpose Zn-MOF Fluorescent Sensor for 2,4-Dinitrophenylhydrazine, Picric Acid, La3+ and Ca2+: Synthesis, Structure, Selectivity, Sensitivity and Recyclability.

Structure Design of Naphthalimide Derivatives: Toward Versatile Photoinitiators for Near-UV/Visible LEDs, 3D Printing, and Water-Soluble Photoinitiating Systems

Synthesis of a Degradation Resistant and Photosensitive Polyimide.

Substituents-triggered Modulation of Structure and Alkali Resistance in Cyano-based Disperse Dyes

Synthesis, growth and characterization of new organic 4-N,N-dimethylamino-4′-N′-methylstilbazolium 2,4-dinitrobenzenesulfonate (DSDNS) single crystal for nonlinear optical applications

Synthesis, optical and thermal characterization of novel thiazolyl heterocyclic azo dye

Investigation of using amine and acetylamine functional units on naphthalimide dyes for photovoltaic devices

A Study of the Electronic Absorption and Emission Spectra of DBDMA Dye: Solvent Effect, Energy Transfer, and Fluorescence Quenching

Synthesis and Characterization of New Azo Compounds Linked to 1, 8-Naphthalimide and Studying Their Ability as Acid-Base Indicators

Synthesis, characterization, and photophysical properties of dicyanoarylamine‐based semi‐aromatic polymers

Photochemistry and Photoelectrochemistry of Donor-Pi-Acceptor Azo-Methine Dyes