Dual-wavelength Passively Q-switched Erbium Fiber Laser Based on a SWNT Absorber

Lei Liu,Zheng,Xin Zhao,Songsong Sun,Jinsong Zhu

DOI: https://doi.org/10.1364/fio.2012.fm3g.6

2012-01-01

Abstract:A dual-wavelength, all-fiber, passively Q-switched Erbium laser based on a SWNT saturable absorber is demonstrated, which can simultaneously generate ~μs pulses with ~kHz repetition rate at 1532 nm and 1558 nm wavelength.

What problem does this paper attempt to address?

Dual-wavelength passively Q-switched Erbium doped fiber laser based on an SWNT saturable absorber

Lei Liu,Zheng Zheng,Xin Zhao,Songsong Sun,Yusheng Bian,Yalin Su,Jiansheng Liu,Jinsong Zhu

DOI: https://doi.org/10.1016/j.optcom.2012.11.094

IF: 2.4

2013-01-01

Optics Communications

Abstract:We report a dual-wavelength, all-fiber, passively Q-switched Erbium doped fiber laser based on a single-wall carbon nanotube saturable absorber. By just varying the pump power to balance the peaks of the Erbium doped fiber gain spectra in the cavity, the laser can operate in the dual-wavelength Q-switching regime without intracavity spectral filters or modulation elements. Our experimental results show that the fiber laser can simultaneously generate Q-switched microsecond pulses at ∼1532nm and ∼1558nm, which have the same repetition rate of tens of kHz and around 0.5nJ pulse energies. Our scheme is quite simple to implement at a low cost.
Dual-wavelength Passively Q-Switched Single-Frequency Fiber Laser.

Yuanfei Zhang,Changsheng Yang,Zhouming Feng,Huaqiu Deng,Mingying Peng,Zhongmin Yang,Shanhui Xu

DOI: https://doi.org/10.1364/oe.24.016149

IF: 3.8

2016-01-01

Optics Express

Abstract:We propose a compact dual-wavelength Q-switched single-frequency fiber laser based on a 17-mm-long home-made highly Er3+/Yb3+ co-doped phosphate fiber (EYDPF) and a semiconductor saturable absorber mirror (SESAM). The short cavity length and a polarization-maintaining fiber Bragg grating (PM-FBG) ensure that only one longitudinal mode is supported by each reflection peak. The maximum pulse energy of more than 34.5 nJ was realized with the shortest pulse duration of 110.5 ns and the Q-switched fiber laser has a repetition rate reaching over 700 kHz with a temporal synchronization of pulses at two wavelengths. Besides, the optical signal-to-noise ratio (OSNR) of larger than 64.5 dB was achieved.
Dual-wavelength and Wavelength-Tunable Passively Q-switched 3um Fiber Laser Based on a Bulk PtSe2

Shurong Jiang,Chen Wei,Le Zheng,Hongrong Zhou,Han Zhang,Jing Zhang,Yong Liu

DOI: https://doi.org/10.1117/12.2602544

2021-01-01

Abstract:We report a dual-wavelength tunable passively Q-switched Er3+ -doped ZBLAN fiber laser at ~3 nm using a bulk PtSe2 as a saturation absorber. Stable pulses were generated for average output power of 504.0 mW at 72.9 kHz repetition rate. The corresponding pulse width and pulse energy were measured to be 1.26 μs and 6.92 μJ, respectively. By tuning the feedback angle of the plane ruled grating, the spectra show simultaneous dual-wavelength pulsed operations with tuning range of 51.5 nm (2745.5-2797.0 nm) at the launched pump of 2.27 W.
Dual-Wavelength Passively Q-Switched Yb-Doped Fiber Laser Based on Ws2 Saturable Absorber and Intracavity Polarization

G. Hu,M. Zhang,L. Chen,T. Li,R. C. T. Howe,X. Zhao,Z. Zheng,T. Hasan

DOI: https://doi.org/10.1364/cleo_si.2016.stu1r.6

2016-01-01

Abstract:We demonstrate a self-starting dual-wavelength ytterbium-doped fiber laser Q-switched by using a solution processed few-layer tungsten disulfide (WS2)-polymer composite saturable absorber, operating at the wavelength of 1030.2 nm and 1034.5 nm, respectively.
A Nanosecond Q-switched Fiber Laser Based on Step-Index Multimode Fiber

N. Li,M. Guo,W. Y. Zhang,J. Zhang,Z. X. Guo,T. Q. Zheng,Y. Z. Li,S. R. An,L. J. Song

DOI: https://doi.org/10.1088/1555-6611/ac089f

IF: 1.2

2021-01-01

Laser Physics

Abstract:A nanosecond passively Q-switched fiber laser using a single mode-step-index-multimode-single mode fiber (SMF-SIMF-SMF) device as the saturable absorber (SA) is demonstrated. Such SMF-SIMF-SMF device operates based on nonlinear multimode interference. A stable Q-switched erbium-doped fiber laser at 1546 nm was realized with a repetition rate varying from 99 kHz to 150 kHz and the shortest pulse duration of 740 ns. At the maximum pump power of 800 mW, the maximum pulse energy of 97.86 nJ at an average output power of similar to 14.7 mW was obtained. Our results indicate that the SMF-SIMF-SMF structures can be used as effective SAs for nanosecond pulse generation.
Yb- and Er-doped fiber laser Q-switched with an optically uniform, broadband WS 2 saturable absorber

M. Zhang,Guohua Hu,Guoqing Hu,R. C. T. Howe,L. Chen,Z. Zheng,T. Hasan

DOI: https://doi.org/10.1038/srep17482

IF: 4.6

2015-01-01

Scientific Reports

Abstract:We demonstrate a ytterbium (Yb) and an erbium (Er)-doped fiber laser Q-switched by a solution processed, optically uniform, few-layer tungsten disulfide saturable absorber (WS 2 -SA). Nonlinear optical absorption of the WS 2 -SA in the sub-bandgap region, attributed to the edge-induced states, is characterized by 3.1% and 4.9% modulation depths with 1.38 and 3.83 MW/cm 2 saturation intensities at 1030 and 1558 nm, respectively. By integrating the optically uniform WS 2 -SA in the Yb- and Er-doped laser cavities, we obtain self-starting Q-switched pulses with microsecond duration and kilohertz repetition rates at 1030 and 1558 nm. Our work demonstrates broadband sub-bandgap saturable absorption of a single, solution processed WS 2 -SA, providing new potential efficacy for WS 2 in ultrafast photonic applications.
Switchable, Dual-Wavelength Passively Mode-Locked Ultrafast Fiber Laser Based on a Single-Wall Carbon Nanotube Modelocker and Intracavity Loss Tuning.

Xin Zhao,Zheng,Lei Liu,Ya Liu,Yaxing Jiang,Xin Yang,Jinsong Zhu

DOI: https://doi.org/10.1364/oe.19.001168

IF: 3.8

2011-01-01

Optics Express

Abstract:We demonstrate a dual-wavelength passively mode-locked soliton fiber laser based on the single-wall carbon nanotube saturable absorber. By using a simple scheme of adjusting the intracavity loss, the gain profile of the erbium-doped fiber laser is effectively controlled. Besides operating at a single wavelength, the laser is able to simultaneously generate sub-picosecond pulses at both ~1532 and 1557 nm wavelength. The mode-locking wavelength can also be quickly switched from one wavelength to the other by changing the intracavity loss with a tunable attenuator.
Multi-color Q-switched of Neodymium-Doped All-Fiber Laser Based on Tungsten Disulfide Saturable Absorber

Rong Xiaofeng,Yang Yumin,Liu Xuefei,Xiao Wenjun,Yang Cheng,Wang Zhen,Liu Zhaohui,Xiao Yuanni,Wang Degui,Xu Huiying,Cai Zhiping

DOI: https://doi.org/10.1007/s10854-022-08946-8

2022-01-01

Journal of Materials Science Materials in Electronics

Abstract:In this paper, a Q-switched and three-color operation of Neodymium-doped silica all-fiber laser is realized, in which, a few-layer transition metal dichalcogenides WS 2 is pioneered to be used as a saturable absorber (SA). The compact and simple linear cavity contains homemade fiber mirrors by directly depositing a multilayer coating the SiO 2 /Ta 2 O 5 dielectric films on fiber end-face. In particular, by inserting the WS 2 -SA into the FP laser cavity, it is found that a stable Q-switching operation was achieved with the higher signal-to-noise ratios (SNR) of 60.76 dB, and the shortest pulse duration of 990 ns, as well as the maximum repetition rate of 124.4 kHz. Meanwhile, the maximum average output power and maximum pulse energy are close to 8.9 mW and 71.5 nJ, respectively. This is, the first demonstration of compact WS 2 -based neodymium-doped all-fiber laser operation at 1081.9, 1091.3 and 1100.1 nm.
All-fiber passively Q-switched erbium-doped laser with Cr<SUP>2+</SUP>:ZnSe nanocrystals saturable absorber

Fengqiong Long,Shougui Ning,Wei Zhang,Shutong Wang,Huomu Yang,Hong Zhang,Guoying Feng,Shouhuan Zhou

DOI: https://doi.org/10.1088/1555-6611/ab8233

IF: 1.2

2020-01-01

Laser Physics

Abstract:We experimentally demonstrate an all-fiber Q-switched erbium-doped laser using polyvinyl alcohol-based Cr2+:ZnSe nanocrystals (NCs) as saturable absorbers (SAs). The Cr2+:ZnSe NCs were produced by femtosecond laser ablation, and were spherical, with an average radius of about 107 nm. The nonlinear saturable absorption was characterized with a saturable optical intensity of 20 MW cm(-2) and a modulation depth of similar to 24%. By placing the SA inside an erbium-doped fiber (EDF) laser cavity, a stable 3.152 mu s pulse with a repetition rate of 34.452 kHz centered at 1564 nm was achieved, when pumped at the maximum pumping power of 300 mW. The maximum pulse energy reached 33 nJ and the signal-to-noise ratio was 48 dB. The results indicate that Cr-2 +/-:ZnSe NCs are promising for the development of a stable all-fiber passively Q-switched EDF laser.
Multi-Wavelength, Passively Q-Switched, Single-Frequency Fiber Laser

Kunyi Li,Huaqiu Deng,Changsheng Yang,Wei Lin,Xianchao Guan,Qilai Zhao,Yi Zhou,Wenlong Wang,Zhongmin Yang,Shanhui Xu

DOI: https://doi.org/10.1109/lpt.2019.2933168

IF: 2.6

2019-01-01

IEEE Photonics Technology Letters

Abstract:A passively Q-switched single-frequency fiber laser with stable multi-wavelength operation is presented in this report. The laser cavity is constructed by using a 13-mm Er3+/Yb3+ co-doped phosphate fiber with a multi-channel fiber Bragg grating and a semiconductor saturable absorber mirror attached to each fiber end, respectively. Quad-wavelength pulsed lasers are obtained and all of them maintain single-frequency operation. By controlling the pump power and the temperature of laser cavity, the Q-switched pulse operation is realized with repetition rates range of 126.6–350.9 kHz, a narrowest pulse duration of 104 ns, and a maximum pulse energy of 55.4 nJ. To the best of our knowledge, this is the first study to realize a Q-switched fiber laser operating at multiple wavelengths with single longitudinal mode. Furthermore, the evolutions of the pulse energy and repetition rates for different wavelength numbers are further analysis theoretically. This type of single-frequency pulsed fiber laser has extensive application prospect in fiber sensing and lidar systems.
The generation and observation of pulses with switchable single/dual wavelengths and tunable bandwidth from a SWNT mode-locked Er-doped fiber laser

Guoqing Hu,Chen Wang,Kai Chen,Junyue Wen,Guowen Guo,Ya Liu,Guangwei Chen,Lianqing Zhu

DOI: https://doi.org/10.1016/j.optlastec.2022.108715

2023-02-01

Abstract:Mode-locked pulse outputs with switchable single/dual wavelengths and widely tunable spectral bandwidth are demonstrated by fully exploiting multiple soliton formation mechanisms combining single-wall carbon nanotube, intracavity loss tuning and nonlinear polarization rotation. An isolator with single-polarization fiber pigtails is additionally inserted in a ring fiber laser cavity to introduce polarization-dependent loss modulation for gain profile tuning and nonlinear polarization rotation. Mode-locked by a home-made single-wall carbon nanotube saturable absorber, switchable single/dual-wavelength pulses centered in the 1530- or/and 1550-nm gain regions of erbium-doped fiber are experimentally observed by tuning the intracavity loss to tilt the gain profile. Moreover, the spectral bandwidths of single-wavelength pulses centered in the 1530- and 1550 nm regions could be continuously tuned from 2.4 to 4.0 nm, and 2.7 to 9.0 nm, respectively. Such widely tunable spectral bandwidths are attributed to hybrid mode-locked mechanisms combining the nonlinear polarization rotation and single-wall carbon nanotube. Our results give a deep insight into the well-controlled gain profile tuning and provide a relatively simple setup and method to obtain bandwidth-tunable, wavelength-switchable pulse outputs, showing the potential to meet various requirements of ultrafast laser applications.

optics,physics, applied
Dual-wavelength Bi 2 Se 3 -Based Passively Q-switching Nd 3+ -Doped Glass All-Fiber Laser

Xiaofeng Rong,Saiyu Luo,Wensong Li,Shuisen Jiang,Xigun Yan,Xiaofeng Guan,Zhiyong Zhou,Bin Xu,Nan Chen,Degui Wang,Huiying Xu,Zhiping Cai

DOI: https://doi.org/10.3788/col201816.020016

IF: 2.56

2018-01-01

Chinese Optics Letters

Abstract:We demonstrate a dual-wavelength passively Q-switched Nd 3+ -doped glass fiber laser using a few-layer topological insulator Bi 2 Se 3 as a saturable absorber(SA) for the first time, to the best of our knowledge. The laser resonator is a simple and compact linear cavity using two fiber end-facet mirrors. The SA is fabricated by Bi 2 Se 3 /polyvinyl alcohol composite film. By inserting the SA into the laser cavity, a stable Q-switching operation is achieved with the shortest pulse width and maximum pulse repetition rate of 601 ns and 205.2 kHz,respectively. The maximum average output power and maximum pulse energy obtained are about 6.6 mW and 38.8 nJ, respectively.
Ultra-Compact Q-Switched Single-Frequency Pulsed Fiber Lasers

Shanhui Xu,Yuanfei Zhang,Zhouming Feng,Changsheng Yang,Zhongmin Yang

DOI: https://doi.org/10.1364/acpc.2016.ath3a.2

2016-01-01

Abstract:We present an ultra-compact passively Q-switched single-frequency fiber laser based on a home-made highly Er 3+ /Yb 3+ co-doped phosphate fiber (EYDPF) and a semiconductor saturable absorber mirror (SESAM). An effective cavity length of less than 20 millimeters ensures a stably single-frequency operation of the Q-switched fiber laser. By employing a SESAM as the Q-switching, the narrowest pulse duration of sub-100 ns is realized, and the repetition rate of the Q-switched fiber laser reaches over 600 kHz. In addition, the achieved linear polarization extinction ratio is more than 25.0 dB.
InAs/GaAs quantum dot semiconductor saturable absorber for controllable dual-wavelength passively Q-switched fiber laser.

X Wang,Y J Zhu,C Jiang,Y X Guo,X T Ge,H M Chen,J Q Ning,C C Zheng,Y Peng,X H Li,Z Y Zhang

DOI: https://doi.org/10.1364/OE.27.020649

IF: 3.8

2019-01-01

Optics Express

Abstract:We experimentally demonstrate the first use of 1550-nm InAs/GaAs quantum dot semiconductor saturable absorber mirror (QD-SESAM) in the dual-wavelength passively Qswitched (QS) erbium doped fiber (EDF) laser. The dual-wavelength QS lasing was obtained at a pump threshold of 180 mW with the average output power of 2.2 mW and the spacing between the two lasing wavelengths is 14 nm. A large absorption ranging from 1520 to 1590 nm has been realized when no substrate rotation was employed during the molecular beam epitaxy growth of the QD-SESAM indicating the potential to generate a 60 nm spacing of the dual-wavelength QS lasing peaks by changing the positions in the QD-SESAM and replacing EDF by co-doped fiber as gain medium. These results have provided a new opportunity towards achieving the stable and wide wavelength-tunable dual-modes fiber lasers. (C) 2019 Optical Society of America under the terms of the OSA Open Access Publishing Agreement
Sub-15-ns Passively Q-Switched Er:YSGG Laser at $2.8~\mu$ M with Fe:ZnSe Saturable Absorber

Yuzhao Zhang,Bin Xu,Qingyu Tian,Zhengqian Luo,Huiying Xu,Zhiping Cai,Dunlu Sun,Qingli Zhang,Peng Liu,Xiaodong Xu,Jian Zhang

DOI: https://doi.org/10.1109/lpt.2019.2902473

IF: 2.6

2019-01-01

IEEE Photonics Technology Letters

Abstract:At present, pulse widths of passively Q-switched mid-infrared lasers at similar to 2.8 mu m have been limited to be at least several hundreds of nanoseconds. In this letter, by configuring a compact laser resonator, we report on diode-pumped continuous-wave and passively Q-switched mid-infrared Er:YSGG lasers. Laser emission at 2797 nm is achieved with a maximum output power of 0.63 W and slope efficiency of 13.9% in continuous-wave mode. Using polycrystalline Fe:ZnSe as saturable absorber, the passively Q-switched operation is also realized with the narrowest pulse width of about 14.6 ns, which is believed to be the shortest pulse for passively Q-switched mid-infrared lasers. The generated maximum pulse energy and peak power are 5.05 mu J and 345.8 W, respectively.
Passively Q-switched 2.8-μm nanosecond fiber laser

Chen Wei,Xiushan Zhu,Robert A. Norwood,Nasser G. Peyghambarian

DOI: https://doi.org/10.1109/LPT.2012.2215021

2012-01-01

Abstract:A diode-pumped erbium ion-doped single-mode ZBLAN fiber laser passively Q-switched by a Fe 2+: ZnSe crystal is reported. Mid-infrared (MIR) pulses at 2.8 μm with a pulse energy of 2.0 μJ and pulse duration of 370 ns, corresponding to a peak power of 5.34 W, are achieved at a repetition rate of 161 kHz. Our experiment demonstrates that Fe 2+: ZnSe crystal is a promising Q-switching element for high power pulsed MIR fiber lasers. © 2012 IEEE.
Passively Q-switched Erbium-Doped Fiber Laser Using a Graphene Saturable Absorber

Z. Z. Dong,H. P. Li,H. D. Xia,Y. Liu,Z. G. Wang,Y. F. Chen

DOI: https://doi.org/10.1364/acpc.2012.as1a.2

2012-01-01

Abstract:We demonstrate a graphene-based passively Q-switched erbium-doped fiber laser. The laser produces stable pulses with a typical pulse width of ~ 9.0 μs at a pulse repetition rate ranging from 8.3 to 12.5 kHz.
Semiconductor Saturable Absorber Mirror Passively Q-switched Fiber Laser Near 2 Μm.

Weiqiang Yang,Jing Hou,Bin Zhang,Rui Song,Zejin Liu

DOI: https://doi.org/10.1364/ao.51.005664

2012-01-01

High Power Laser and Particle Beams

Abstract:A passively Q-switched fiber laser near 2 μm is achieved with a semiconductor saturable absorber mirror (SESAM) as a saturable absorber. Stable Q-switched pulses are generated from an extremely compact setup with a central wavelength of 1958.2 nm. Under the bidirectional pump configuration, the repetition rate of the fiber laser can be widely tuned from 20 to 80 kHz by increasing the pump power at the same time the pulse width decreases from 1 μs to 490 ns. When the incident pump power is 1.3 W, the average output power, the pulse repetition rate, the pulse width, and the highest single pulse energy are 91 mW, 80 kHz, 490 ns, and 1.14 μJ, respectively. To further optimize the system configuration, the pulse width can be reduced to 362 ns when the cavity length is reduced.
Q-Switched Mid-Infrared Er<sup>3+</sup>: ZBLAN Fiber Laser at 2.8 μm with a MXene-Based Saturable Absorber

Liqiang Zhou,Chen Wei,Dongsheng Wang,Hao Chi,Qingru Li,Han Zhang,Yong Liu

2019-01-01

Abstract:We report a passively Q-switched Er-doped fiber laser at 3 μm by using MXene as a saturable absorber for the first time. The laser generates 2.08 μs pulses with 517 mW average output power at 78.12 kHz repetition rate.
Passively Q-Switched 2.8-$\Mu{\rm M}$ Nanosecond Fiber Laser

Chen Wei,Xiushan Zhu,Robert A. Norwood,N. Peyghambarian

DOI: https://doi.org/10.1109/lpt.2012.2215021

IF: 2.6

2012-01-01

IEEE Photonics Technology Letters

Abstract:A diode-pumped erbium ion-doped single-mode ZBLAN fiber laser passively Q-switched by a Fe 2+ :ZnSe crystal is reported. Mid-infrared (MIR) pulses at 2.8 μm with a pulse energy of 2.0 μJ and pulse duration of 370 ns, corresponding to a peak power of 5.34 W, are achieved at a repetition rate of 161 kHz. Our experiment demonstrates that Fe 2+ : ZnSe crystal is a promising Q-switching element for high power pulsed MIR fiber lasers.

Dual-wavelength Passively Q-switched Erbium Fiber Laser Based on a SWNT Absorber

Dual-wavelength passively Q-switched Erbium doped fiber laser based on an SWNT saturable absorber

Dual-wavelength Passively Q-Switched Single-Frequency Fiber Laser.

Dual-wavelength and Wavelength-Tunable Passively Q-switched 3um Fiber Laser Based on a Bulk PtSe2

Dual-Wavelength Passively Q-Switched Yb-Doped Fiber Laser Based on Ws2 Saturable Absorber and Intracavity Polarization

A Nanosecond Q-switched Fiber Laser Based on Step-Index Multimode Fiber

Yb- and Er-doped fiber laser Q-switched with an optically uniform, broadband WS 2 saturable absorber

Switchable, Dual-Wavelength Passively Mode-Locked Ultrafast Fiber Laser Based on a Single-Wall Carbon Nanotube Modelocker and Intracavity Loss Tuning.

Multi-color Q-switched of Neodymium-Doped All-Fiber Laser Based on Tungsten Disulfide Saturable Absorber

All-fiber passively Q-switched erbium-doped laser with Cr<SUP>2+</SUP>:ZnSe nanocrystals saturable absorber

Multi-Wavelength, Passively Q-Switched, Single-Frequency Fiber Laser

The generation and observation of pulses with switchable single/dual wavelengths and tunable bandwidth from a SWNT mode-locked Er-doped fiber laser

Dual-wavelength Bi 2 Se 3 -Based Passively Q-switching Nd 3+ -Doped Glass All-Fiber Laser

Ultra-Compact Q-Switched Single-Frequency Pulsed Fiber Lasers

InAs/GaAs quantum dot semiconductor saturable absorber for controllable dual-wavelength passively Q-switched fiber laser.

Sub-15-ns Passively Q-Switched Er:YSGG Laser at $2.8~\mu$ M with Fe:ZnSe Saturable Absorber

Passively Q-switched 2.8-μm nanosecond fiber laser

Passively Q-switched Erbium-Doped Fiber Laser Using a Graphene Saturable Absorber

Semiconductor Saturable Absorber Mirror Passively Q-switched Fiber Laser Near 2 Μm.

Q-Switched Mid-Infrared Er<sup>3+</sup>: ZBLAN Fiber Laser at 2.8 μm with a MXene-Based Saturable Absorber

Passively Q-Switched 2.8-$\Mu{\rm M}$ Nanosecond Fiber Laser