Abstract:The CH-Structure has been studied at the IAP Frankfurt and at GSI for several years. Compared with the IH structure (110-mode), the CH structure (210-mode) can operate at higher frequencies (150 700 MHz) and can accelerate ions to higher energies (up to 150 AMeV). Detailed Microwave Studio (MWS) simulations were performed for this structure. Since a multi-gap cavity can be approximated as a quasi-periodic structure, it is possible to analyse one βλ/2-cell at an energy corresponding to the cavity centre. A reduced copper conductivity of 85% was adopted in effective shunt impedance calculations. Geometry variations with respect to RF frequency and shunt impedance can be performed rapidly by that method in the first stage of optimization. Using the transit time factor calculated by the beam dynamics simulation code LORASR, effective shunt impedances from 100 MΩ/m down to 45 MΩ/m were obtained for the energy range from 6MeV to 66 MeV by this method. The RF frequency was 352 MHz. A systematic analysis of the influence of the cell number in long CH-cavities on the effective shunt impedance is presented. Actually, a 70 MeV, 70 mA, 352 MHz proton linac design for GSI Darmstadt is developed. About 12 CH-cavities will cover the energy range from 3 MeV up to the final energy, the DTL total length will be around 22m. INTRODUCTION The Interdigital H-type (IH) structure is well known for its high shunt impedance at low beta values. It is successfully used as front part for ion linacs like the Unilac at GSI [1] or the CERN Linac3 [2] and for rare isotope acceleration. Since a couple of years, a new type of H-structure was proposed and studied at IAP, Frankfurt and GSI, Darmstadt, that is the Cross Bar H-type (CH) structure. Compared with the IH-structure, the CHstructure is providing new features. Working in the H21 mode, the transverse cavity dimensions are significantly larger than that of the IH-cavity at a given frequency and velocity profile, thus it can work at higher frequencies up to around 700 MHz. This allows to close the velocity gap with respect to attractive structures at the low energy end of Coupled Cavity Linacs CCL. It can be designed for operation at about 350 MHz in the first section and at 700 MHz in the high-energy section up to about 150 AMeV. Furthermore, the CH cavity exceeds by far the mechanical rigidity of the IH cavity. This opens the possibility to develop superconducting multi-cell cavities as well [3]. A set of formulas based on a simple field model was derived for H-type structures to describe the main RF parameters as a function of the geometrical dimensions. A normal conducting 70 MeV, 70 mA proton injector based on a 3 Mev RFQ followed by a CH-DTL is designed for the future FAIR facility at GSI. The beam dynamics [4] and the cavity design are studied in parallel. The construction of a model cavity will start this year. In the following sections we present the results got from cavity simulations for room temperature CH structures, the emphasis is put on the effective shunt impedance.

Choke-mode damped structure design for the CLIC main Linac

Choke-Mode Damped Structure Design for the Compact Linear Collider Main Linac

Design and Optimization of Compact Linear Collider Main Linac Accelerating Structure

High-Gradient Breakdown Studies of X-Band Choke-Mode Structures

Beam-induced Wakefield Observation in X -Band Choke-Mode Cavities

High Power Test of X-band Single Cell HOM-free Choke-mode Damped Accelerating Structure Made by Tsinghua University

Design of the Compact Linear Collider Main Linac Accelerating Structure Made from Two Halves

A High Phase Advance Damped and Detuned Structure for the Main Linacs of Clic

Design, Fabrication, and High-Gradient Testing of X-band Choke-Mode Damped Structures

Design, fabrication and high-gradient tests of X-band choke-mode structures

Design of the RF waveguide network for the klystron-based CLIC main linac RF module

Design of a 3 GHz Accelerator Structure for the CLIC Test Facility (CTF 3) Drive Beam

A Continuous-Wave Superconducting Linear Accelerator Scheme for the Drive Beam Acceleration of the Compact Linear Collider

Design of the r . t . ch-cavity and perspectives for a new gsi proton linac *

Beam-Based Measurements of Long Range Transverse Wakefields in CLIC Main Linac Accelerating Structure

Tolerance Study of Travelling-Wave Accelerating Structure for the Main Linac of the Klystron-Based First Stage of Compact Linear Collider

Detuned-Structure-Based Beam-Driven Accelerator

Beam-based Measurements of Long-Range Transverse Wakefields in the Compact Linear Collider Main-Linac Accelerating Structure

Modeling and Design of a High-Efficiency Multibeam Klystron

High Gradient Properties of a CLIC Prototype Accelerating Structure Made by Tsinghua University

International Linear Collider Damping Ring Lattice Design with Two Wiggler Sections