Abstract:The ternary polymerization strategy of incorporating different donor and acceptor units forming terpolymers as photovoltaic materials has been proven advantageous in improving power conversion efficiencies (PCEs) of polymer solar cells (PSCs). Herein, a series of low band gap nonconjugated terpolymer acceptors based on two different fused-ring electron-deficient building blocks (IDIC16 and ITIC) with adjustable photoelectric properties were developed. As the third component, ITIC building blocks with a larger π-conjugation structure, shorter solubilizing side chains, and red-shifted absorption spectrum were incorporated into an IDIC16-based nonconjugated copolymer acceptor PF1-TS4, which built up the terpolymers with two conjugated building blocks linked by flexible thioalkyl chain-thiophene segments. With the increasing ITIC content, terpolymers show gradually broadened absorption spectra and slightly down-shifted lowest unoccupied molecular orbital levels. The active layer based on terpolymer PF1-TS4-60 with a 60% ITIC unit presents more balanced hole and electron mobilities, higher photoluminescence quenching efficiency, and improved morphology compared to those based on PF1-TS4. In all-polymer solar cells (all-PSCs), PF1-TS4-60, matched with a wide band gap polymer donor PM6, achieved a similar open-circuit voltage (Voc) of 0.99 V, a dramatically increased short-circuit current density (Jsc) of 15.30 mA cm–2, and fill factor (FF) of 61.4% compared to PF1-TS4 (Voc = 0.99 V, Jsc = 11.21 mA cm–2, and FF = 55.6%). As a result, the PF1-TS4-60-based all-PSCs achieved a PCE of 9.31%, which is ∼50% higher than the PF1-TS4-based ones (6.17%). The results demonstrate a promising approach to develop high-performance nonconjugated terpolymer acceptors for efficient all-PSCs by means of ternary polymerization using two different A–D–A-structured fused-ring electron-deficient building blocks.This article has not yet been cited by other publications.

Ternary Donor-Insulator-acceptor Systems for Polymer Solar Cells.

Ternary Polymer Solar Cells Based-on Two Polymer Donors with Similar HOMO Levels and an Organic Acceptor with Absorption Extending to 850 Nm

Enhanced Photovoltaic Performances Via Ternary Blend Strategy Employing a Medium-Bandgap D-A Type Alternating Copolymer As the Single Donor

Ternary Polymer Solar Cells Enabled Using Two Donor Polymers with Broad Absorption and Cascade LUMO Levels

Enhancing the Performance of Polymer Solar Cells by Using Donor Polymers Carrying Discretely Distributed Side Chains.

Ternary Solar Cells Via Ternary Polymer Donors and Third Component PC71BM to Optimize Morphology with 13.15% Efficiency

Nonconjugated Terpolymer Acceptors with Two Different Fused-Ring Electron-Deficient Building Blocks for Efficient All-Polymer Solar Cells

Improving Miscibility of Polymer Donor and Polymer Acceptor by Reducing Chain Entanglement for Realizing 18.64% Efficiency All Polymer Solar Cells

Efficient Non-Halogenated Solvent Processed Ternary All-Polymer Solar Cells with A Favorable Morphology Enabled by Two Well-Compatible Donors.

High‐Performance Terpolymers with Well‐Defined Structures Facilitate PCE over 19% for Polymer Solar Cells

A conjugated donor-acceptor block copolymer enables over 11% efficiency for single-component polymer solar cells

Ternary Polymer Solar Cells with Low-Cost P3HT as the Second Donor by the Complementary Absorption Region from Long-Wavelength to Medium-Wavelength Regions Forming Cascaded HOMO and LUMO Energy Levels

Nonhalogenated Solvent-Processed Efficient Ternary All-Polymer Solar Cells Enabled by the Introduction of a Naphthyloxy Group into the Side Chain of Polymer Donors

Designing a Highly Crystalline Polymer Donor with Alkylsilyl and Fluorine Substitution to Achieve Efficient Ternary Organic Solar Cells

Ternary All-Polymer Solar Cells with Two Synergetic Donors Enable Efficiency over 14.5%

Donor-acceptor-type copolymers based on a naphtho[1,2-c:5,6-c]bis(1,2,5-thiadiazole) scaffold for high-efficiency polymer solar cells.

Largely improved bulk-heterojunction morphology in organic solar cells based on a conjugated terpolymer donor via a ternary strategy

Ternary Organic Solar Cells with Minimum Voltage Losses

Terpolymer Strategy Toward High-Efficiency Polymer Solar Cells: Integrating Symmetric Benzodithiophene and Asymmetrical Thieno[2,3-f]benzofuran Segments

Significantly Enhanced Molecular Stacking in Ternary Bulk Heterojunctions Enabled by an Appropriate Side Group on Donor Polymer

High-Efficiency Ternary Organic Solar Cells with a Good Figure-of-Merit Enabled by Two Low-Cost Donor Polymers