Abstract:Thermal shrinkage has for long been a critical issue in nonwoven industrial applications. A dimensionally stable nonwoven web with excellent mechanical property was achieved by heat treatment with tension [taut annealed (TA)] instead of annealing under free state [free annealed (FA)], while the original high porosity was not affected. To better understand the fundamental structure-property relationship, these two different heat treatments' effects on the thermal behaviors, morphology, and phase structures of poly(phenylene sulfide) (PPS) nonwovens were elucidated via a combination of different experimental techniques such as temperature-modulated differential scanning calorimetry (DSC), two-dimensional wide-angle X-ray diffraction, two-dimensional small-angle X-ray scattering, and polarized Raman spectroscopy. It is evidenced that no obvious online stress-induced crystallization occurs during the melt-blowing process, making virgin PPS fibers mostly in the amorphous state. However, experimental results confirm that a certain amount of mesophase or constrained amorphous exists in the virgin PPS fibers without any presence of crystallites. After annealing, the DSC melting curves of both TA and FA PPS nonwovens exhibit endothermic annealing peaks, the origin of which is interpreted as the relaxation and devitrification of the rigid amorphous phase. However, the annealing peak position of the FA sample is always higher than that of the TA sample, which is reported for the first time. As compared with the FA sample annealed at the same temperature, TA PPS nonwovens reveal lower crystallinity and slightly larger lamellar long period (L-p) but a higher level of macroscopic fiber alignment and molecular chain orientation. These morphology and microstructure differences provide a good explanation for the superior mechanical property of TA PPS nonwovens with higher elastic modulus and tensile strength. The results are helpful in deepening the understanding of essential physical pictures of PPS nonwovens and promoting the development of the high-temperature nonwoven industry.

Effects of Heat Treatment on the Morphology and Performance of Psu Electrospun Nanofibrous Membrane

Effect of Coagulation Bath Temperature on the Structure and Performance of Polyethersulfone Hollow Fiber Membranes by Dry/wet Process

Structure formation and characterization of PVDF hollow fiber membranes by melt-spinning and stretching method

Preparation and Performance of Polyethersulfone Hollow-Fiber Membrane

Effect of Heat Treatment Mode and Aggressive Media on Mechanical Properties of Porous Polytetrafluoroethylene Membranes Fabricated via Electrospinning

Heat treatment for improving performance of inner-side zeolite NaA membranes on composite hollow fibers

Heat-setting Effect on the Morphology and Phase Structures of PPS Nonwovens

The Effects of Spinning Temperature on Morphologies and Properties of Polyethersulfone Hollow Fiber Membranes

Preparation of Super-Hydrophilic Polyphenylsulfone Nanofiber Membranes for Water Treatment

Effects of Heat Treatment on the Properties of Heterogeneous Cation Permeable Membranes from Blends of Poly(Ether Sulfone)/Sulfonated Poly(Phenylene Sulfide) and Phenolphthalein Poly(Ether Ether Ketone)/Sulfonated Poly(Phenylene Sulfide)

Heat-Treated Polyacrylonitrile (pan) Hollow Fiber Structured Packings in Isopropanol (ipa)/water Distillation with Improved Thermal and Chemical Stability

Electrospun Polymer Composite Membrane with Superior Thermal Stability and Excellent Chemical Resistance for High-Efficiency PM2.5 Capture.

A simple and effective approach to regulate and control pore structure of electrospun PTFE nanofiber membrane

Thermal treatment of electrospun polystyrene fibers: microstructural evolution and mechanical behavior

Effects of surface morphology of electrospun polystyrene fiber on its air filtration performance

Effects of coagulation-bath conditions on polyphenylsulfone ultrafiltration membranes

Effect of Experimental Parameters on Morphological, Mechanical and Hydrophobic Properties of Electrospun Polystyrene Fibers

Fabrication of polysulfone membrane with sponge-like structure by using different non-woven fabrics

Influence of Electrospinning Parameters on the Morphology of Electrospun Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) Fibrous Membranes and Their Application as Potential Air Filtration Materials

Enhancement of mechanical and physical properties of electrospun PAN nanofiber membranes using PVDF particles

Controlled preparation of polyimide/polysulfone amide (PI/PSA) porous micro-nano fiber membranes by microemulsion electrospinning for excellent thermal insulation