Abstract:Fiber electrospun mats created using cylindrical collectors have been extensively studied as effective membranes for water treatment. However, the relationships between the properties of electrospun mats and the characteristics and performance of membranes are not well‐established. This research examined two samples with average fiber diameters of 1.8 ± 0.49 μm and 0.47 ± 0.26 μm, which were evaluated as supporting substrates for the separation of MgSO4 ions. The variation in fiber diameter resulted from consistent conditions of voltage, distance, and collector rotation speed, while the injection rates were different, set at 2 mL/h and 0.8 mL/h, respectively. The resulting thin‐film composite (TFC) membrane consists of three layers: the first layer is a mesh polyester that underlies a middle hydrophobic electrospun support layer made from a 20 wt.% polysulfone solution. The third layer is a polyamide layer created through interfacial polymerization, involving a reaction between piperazine (PIP) monomers at a concentration of 2% by weight and trimesoyl chloride (TMC) monomers at a concentration of 0.2% by weight. Due to its hydrophobic nature, PSU repels water monomers from its surface during polymerization. Consequently, surface modification using plasma treatment alters the surface characteristics from hydrophobic to hydrophilic, resulting in the formation of a superior polyamide layer. The results indicate that membranes with larger fiber diameters exhibit a rougher texture. Additionally, the increased void space between the fibers in these membranes leads to an increase in pure water flux that is 92% higher compared to membrane samples with smaller fiber diameters; this higher flux is due to larger pore size. Furthermore, membranes with smaller fiber diameters possess a finer pore structure, resulting in a polyamide layer with fewer defects than membranes with larger fibers. This improved structure achieved a separation efficiency of 68% ± 1.02% for MgSO4, while the membrane with an average fiber diameter of 1.80 ± 0.49 μm demonstrated a separation rate of 20% ± 2.26%. These findings provide a step forward in the development of a theoretical framework for engineering TFC membranes with electrospun mats as supports.

Effects of surface morphology of electrospun polystyrene fiber on its air filtration performance

Effect of Different Surfactants on Performance of Electrospun Ultrafine Nanofiber

Effect of Experimental Parameters on Morphological, Mechanical and Hydrophobic Properties of Electrospun Polystyrene Fibers

Influence of Electrospinning Parameters on the Morphology of Electrospun Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) Fibrous Membranes and Their Application as Potential Air Filtration Materials

Influence of Mixed Solvent in the Morphology and Hydrophobicity of Electrospun Polystyrene Porous Fibers

Electrospun Coarse Modified Polystyrene/carbon Aerogel Nanofibrous Composite Membrane for Effective PM2.5 Air Filtration

Effects of Jet Path on Electrospun Polystyrene Fibers

One-Step Fast Fabrication of Electrospun Fiber Membranes for Efficient Particulate Matter Removal

Improving the Electrospinning Process of Fabricating Nanofibrous Membranes to Filter PM2.5

Performance of Electrospun Polyvinylidene Fluoride Nanofibrous Membrane in Air Filtration

Multifactorial evaluation of an ultra-fast process for electrospinning of recycled expanded polystyrene to manufacture high-efficiency membranes for nanoparticle air filtration

Preparation of Anti-Layered Polyamide-66/Polyacrylonitrile/Polyethersulfone (Pa-66/Pan/pes) Sandwich Structured Membrane for Air Filtration by Electrospinning

Air filtration performance of nanofiber membranes with different morphologies produced by green electrospinning

Study on Filtration Performance of PVDF/PUL Composite Air Filtration Membrane Based on Far-Field Electrospinning

The Effects of Spinning Temperature on Morphologies and Properties of Polyethersulfone Hollow Fiber Membranes

Novel Anti-Fouling Polyethersulfone/polyamide 66 Membrane Preparation for Air Filtration by Electrospinning

Effects of electrospinning conditions on microstructural properties of polystyrene fibrous materials

Electrospinning of Nanofibrous Membrane and Its Applications in Air Filtration: A Review

Research on the process of preparing fiber filtration membrane by centrifugal blowing electrospinning technology

Insight Into the Role of Fiber Diameter on Electrospun Polysulfone Mats

Nude and Modified Electrospun Nanofibers, Application to Air Purification