Abstract:Kapton film is a polymeric material widely used on low-Earth-orbit (LEO) spacecraft surfaces. In the LEO environment, atomic oxygen (AO) is spaceflight materials' most destructive environmental factor. The erosion mechanism of AO on Kapton films has long been an important issue, where the parameter dependence of the AO effect has received increasing attention. Studies of AO energy and cumulative flux have been extensively carried out, while the influence mechanism of the incidence angle and flux density is not fully understood. The AO incidence angle and flux density in space are diverse, which may cause different damage effects on aerospace materials. In this paper, the dependence of the incidence angle and flux density in the damaging effect of AO on Kapton films was investigated using ground-based AO test technology and the reactive molecular dynamics (ReaxFF MD) simulation technique. Firstly, the ground-based experiment obtained the mass loss data of Kapton films under the action of AO with a variable incidence angle and flux density. Then, the mass loss, temperature rise, product, and erosion yield of Kapton during AO impact with different incidence angles and dose rates were calculated using the ReaxFF MD method. The influences of the incidence angle and flux density on the damage mechanism of the AO effect were discussed by comparing the simulation and test results. The results show that the AO effect in the lower incidence angle range (0-60°) is independent of the incidence angle and depends only on the amount of impacted atomic oxygen. AO in the higher incidence angle range (60-90°) has a surface stripping effect, which causes more significant mass loss and a temperature rise while stripping raised macromolecules from rough surfaces, and the erosion effect increases with the increasing incidence angle and amount of impacted atomic oxygen. There is a critical value for the influence of flux density on the AO effect. Above this critical value, AO has a reduced erosive capacity due to a lower chance of participating in the reaction. The amount of each main product from the AO effect varies with the incidence angle and flux density. Nonetheless, the total content of the main products is essentially constant, around 70%. This work will contribute to our understanding of the incidence angle and flux density dependence of the AO effect and provide valuable information for the development of standards for ground simulation tests.

Preparation and Properties of Atomic Oxygen Protective Films Deposited on Kapton by Solvothermal and Sol–gel Methods

Studies on the Erosion Mechanism of Kapton and Its Protective Effect

Ground-based investigations of atomic oxygen erosion behaviors of Al2O3 coating on kapton

Ground-based Investigations of Atomic Oxygen Erosion Behaviors of Kapton and ZnO-siloxane Coatings on Kapton

Atomic Oxygen Adaptability of Flexible Kapton/Al2O3 Composite Thin Films Prepared by Ion Exchange Method

ATOMIC OXYGEN IRRADIATION INDUCED DEGRADATION OF POLYIMIDE WITHOUT AND WITH SILOXANE COATING

In situ formation of POSS layer on the surface of polyimide film and anti-atomic oxygen of SiO 2 /POSS coatings

Atomic oxygen effects on polymers containing silicon or phosphorus: Mass loss, erosion yield, and surface morphology

Reactive molecular dynamics simulation on the disintegration of Kapton, POSS polyimide, amorphous silica, and teflon during atomic oxygen impact using the ReaxFF reactive force-field method

Effect of Coating Thickness on the Atomic Oxygen Resistance of Siloxane Coatings Synthesized by Plasma Polymerization Deposition Technique

Synthesis, Characterization and Properties of ATO/potassium Silicate Film Prepared by Twice Spray Pyrolysis

Dependence of Incidence Angle and Flux Density in the Damage Effect of Atomic Oxygen on Kapton Film

Damage and degradation of mechanical properties of polyimide-based materials under atomic oxygen attack: A molecular dynamics simulation study

Mechanically Robust Irradiation, Atomic Oxygen, and Static-Durable CrO x /CuNi Coatings on Kapton Serving as Space Station Solar Cell Arrays

Reactive molecular dynamics simulation on the disintegration of Kapton and Upilex-S during atomic oxygen impact

Mechanism Analysis and Potential Applications of Atomic Oxygen Erosion Protection for Kapton-Type Polyimide Based on Molecular Dynamics Simulations

Preparation technology and properties of a thin anodic oxide composite film on the surface of an aluminum alloy foil

One-step generating protect film resisting ozone and strong acid on conductive silicone adhesive with atmospheric pressure plasma-assisted

Preparation And Characterization Of Ato/Ps Bilayer Films With Superior Hydrophobicity

PREPARATION OF TRANSPARENT ABRASION-RESISTANT ORGANIC-INORGANIC HYBRID FILM

The atomic oxygen resistant study of a transparent polyimide film containing phosphorus and fluorine