Abstract:<p>In this study, the microstructure evolution and mechanical anisotropy of the extruded Mg-2Zn-0.4Mn-0.4Ce alloy tube during tensile loading along the extrusion direction (ED), 45° towards extrusion direction (45°ED) and transverse direction (TD) were investigated, respectively. The results showed that the initial extruded alloy tube had an obvious {0001} basal fiber texture with the symmetrical pole position deviating about 20° from the RD to ED, which resulted in mechanical anisotropy of the tensile yield stress (TYS) when tensile loading along the ED, 45°ED and TD. The deformation behavior of the alloy tube consisted of three stages. In the yield process, the deformation was dominated by prismatic<a>slip under tensile loading along the ED, while the deformation was dominated by basal<a>slip, next were prismatic<a>slip and pyramidal<c+a>slip under tensile loading both along the 45°ED and TD. In the initial stage after yielding, some extension twin (ETW) formed when tensile loading along the three direction, and the deformations were still dominated by the previous slip systems. In the later part of the deformation, the activation of prismatic<a>slip and the nucleation and expansion of ETW gradually reached saturation under tensile loading along the ED. The dominated prismatic<a>slip was gradually replaced by pyramidal<c+a>slip, and accompanied with a small content of contraction twin (CTW) and double twin (DTW), thus forming a typical texture of [0001]⊥ED. For the deformation both along the 45°ED and TD, dominated prismatic<a>slip and subdominant pyramidal<c+a>slip gradually became the main deformation mode after the saturation of basal<a>slip and ETW, and a small content of CTW and DTW also formed, thus forming the texture of [0001]∥ED-RD plane.</a></c+a></a></c+a></a></a></c+a></a></a></a></p>

Anisotropy of thermal conductivity and mechanical properties in Mg-5Zn-1Mn alloy

Effect of Zn content on microstructure, mechanical properties and thermal conductivity of extruded Mg-Zn-Ca-Mn alloys

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Thermal Characteristics of Mg–Zn–Mn Alloys with High Specific Strength and High Thermal Conductivity

Microstructure, Non-Basal Texture and Strength-Ductility of Extruded Mg-6Bi-3Zn Alloy

Investigation on the anisotropy of mechanical properties along different orientations of an AZ31 hot-extrusion bar

Effect of Mn content on the microstructure and mechanical properties of as-extruded Zn-0.2Mg-Mn (wt%) alloys

Investigation on corrosion behavior and mechanical properties of an extruded Mg-Zn-Al-Sn-Mn alloy

Textural evolution and improved ductility in Zn-0.2Mg-0.8Mn (wt%) alloys at different extrusion temperatures

Effect of Heat Treatment on Microstructure and Mechanical Properties of Mg-5Zn-1Mn Alloy Tube

Microstructural Evolution and Mechanical Properties of Mg-5y-5gd-Xnd-0.5zr Magnesium Alloys at Different States

Effect of Hot Extrusion on Microstructure, Texture, and Mechanical Properties of Mg-Zn-Mn-0.5Ca Alloy

Effects of Icosahedral Phase on Mechanical Anisotropy of As-Extruded Mg-14Li (in Wt%) Based Alloys

Effect of Mg content on the microstructure, texture, and mechanical performance of hypoeutectic extruded Zn-Mg alloys

Microstructure, Tensile Properties and Work Hardening Behavior of an Extruded Mg–Zn–Ca–Mn Magnesium Alloy

Microstructure, Mechanical and Thermal Properties of Mg-0.5Ca-xZr Alloys

Effect of Nd and Y Addition on Microstructure and Mechanical Properties of Extruded Mg-Zn-Zr Alloy

The microstructure evolution and mechanical anisotropy of extruded Mg-2Zn-0.4Ce-0.4Mn alloy tube during tension in different directions

Effect of annealing treatment on texture evolution, microstructure and mechanical properties of an extruded Mg-Gd-Zn-Zr alloy

Microstructure evolution, strengthening mechanisms and deformation behavior of high-ductility Mg−3Zn−1Y−1Mn alloy at different extrusion temperatures