Abstract:Al-Zn-Mg-Cu alloy, as an important lightweight structural material in the aerospace field, has ushered in a broader application space and proposed higher performance requirements. This paper presents the experimental investigation of the effect of Zr content on the microstructure refinement and performance improvement of cast Al-5.8Zn-2.3Mg-1.7Cu alloy, aiming to optimize the additional amount of Zr, refine the alloy grains, and improve the microstructure uniformity and mechanical properties. The chemical component, phase, and microstructure were observed by inductively coupled plasma, X-ray diffraction, optical microscope and scanning electron microscope; the hardness and mechanical properties were measured by Brinell hardness tester and tensile testing machine. The addition of different contents of Zr into the alloy can form fine dispersed or primary coarse Al3Zr phase, which has a significant effect on the microstructure and mechanical properties of the alloy. The results indicate that the addition of 0.05 wt% Zr does not significantly improve the grain refinement and mechanical properties, but the Brinell hardness reaches the maximum. As the Zr content rises, the grain refinement effect becomes more obvious, while the mechanical properties first increase and then decrease. The addition amount reaches 0.20 wt%, the second dendrite arm spacing is the smallest, the ultimate tensile strength, yield strength and elongation at room temperature reach the maximum of 296.74 MPa, 249.41 MPa and 8.26%, respectively. When the amount of Zr added exceeds 0.20 wt%, the existence of coarse and brittle primary Al3Zr phase reduces the mechanical properties, and the fracture morphology changes from ductile to brittle intergranular fracture.

Effects of Ni Addition on the Microstructure and Compressive Deformation Behavior in Zr–Cu–Ni Martensitic Alloys

Effects of Zr Addition on the Deformation Behavior, Microstructure and Mechanical Properties of Dental Ti Alloys

Micro-alloying effects of Ni on the microstructure and mechanical properties of an Al-Zn-Mg-Cu-Sc-Zr alloy

Improving the Microstructure and Mechanical Properties of Zr-Ti Alloy by Nickel Addition

Effect of Ni addition on the microstructure, conductivities and mechanical properties of as-cast Al-Fe alloys

Effects of Ti Addition on Microstructure, Mechanical Properties and Corrosion Resistance of the Cu-Zn-Ni Alloy

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Effects of Ni content on microstructure and wear behavior of Al–13Si–3Cu–1Mg-xNi-0.6Fe-0.6Mn alloys

Analysis of Ni-Cu Interaction in Aluminum-Based Alloys: Hardness, Tensile and Precipitation Behavior

Effect of nickel on the microstructure and mechanical property of die-cast Al–Mg–Si–Mn alloy

Effects of Low Nickel Content on Microstructure and High-Temperature Mechanical Properties of Al-7Si-1.5Cu-0.4Mg Aluminum Alloy

Microstructures and Mechanical Properties of Cast Nb-Ti-Si-Zr Alloys

Effects of Ni Addition on the Mechanical and Electrical Properties of Cu-15 Mass%Cr In-Situ Composites

Alloying Effect on the Microstructure and Property of Single Crystal Ni 3 Al Alloys

Effect of Zr addition on the microstructure, phase transformation and mechanical property of Ni 50 Mn 25 Ga 17 Cu 8 alloy

Microstructure and properties of a novel ultra-high strength, high elasticity and high plasticity Cu–20Ni–20Mn-0.3Nb-0.3Cr-0.1Zr alloy

Effect of Aluminum, Iron and Chromium Alloying on the Structure and Mechanical Properties of (Ti-Ni)-(Cu-Zr) Crystalline/Amorphous Composite Materials

Effects of Zr and Sr on microstructure and mechanical properties of cast Al–Si–Cu–Ni–Mg alloy

Effect of Ni content on the wear behavior of Al-Si-Cu-Mg-Ni/SiC particles composites

Microstructure and Mechanical Properties of Cu–12Al–xNi Alloy Prepared Using Powder Metallurgy

Influence of Zr content on microstructure and mechanical properties of As-cast Al-Zn-Mg-Cu alloy