Abstract:An experimental perovskite solar cell (PSC) with the structure Au/Spiro-MeOTAD/CH3NH3PbI3/PEDOT:PSS/ITO was fabricated. The measurements of main photovoltaic characteristics were provided. The current-voltage dependences (I-V curves) were measured conducted in the voltage range from -1V to 1V. During the measurements, the corresponding values were calculated of the short-circuit current density(Jsc) and open-circuit voltage(Uoc) were obtained as 1.23 mA/cm2 and 0.19 V, respectively. Subsequently, an analytical model corresponding to this structure was formulated. For modeling the parameters of the perovskite solar cell, the Comsol Multiphysics environment was used, this environment is based on the finite element method. The relevant computations were provided to obtain the corresponding values of the short-circuit current density and open-circuit voltage as 3.29 mA/cm2 and 0.2 V, respectively, with the maximum theoretically calculated power of this structure being 0.11 W. The experimental outcomes were juxtaposed with the predictions of the analytical computations, and the modeling results were empirically validated. An analytically accomplished model of the same structure was built by adding an electron transport layer (ETL). An organic material BCP (Bathocuproine) was used as an supplementary ETL layer. During the optimization of the PSC, the main datums were mathematically counted. Such values as the short-circuit current density of 10.17 mA/cm2, open-circuit voltage of 1.2 V, and the maximum power value of Au/BCP/Spiro-MeOTAD/CH3NH3PbI3/PEDOT:PSS/ITO structure, which is 3.21 W were rated. A comparison of the volt-ampere characteristics of perovskite cells in dark and light modes was conducted for primary and optimized structures. The main parameters, obtained during the modeling of the experimental sample and subsequent model optimization, were compared. Specifically one of the key parameters of solar cell heterostructures the fill factor was evaluated and found to have increased from 16.52% to 25.00%, respectively. The light-sensitive behavior of the perovskite cell were visibly enhanced.

Performance Optimization by Considering Current Matching in Polymer Tandem Solar Cells

Analysis of the Effect of Active Layer Thickness on Polymer Solar Cell Performance Based on Optical and Opto-Electronic Model

Overcoming the Thickness Paradox: Systematical Optimization of Inverted Polymer Solar Cells

Optimizing tandem solar cells efficiency through current matching technique in lead-free perovskite/c-Si and lead-free perovskite/CIGS absorbers

Optical Design of Monolithic Two-Terminal Perovskite/Si Tandem Solar Cells for Efficient Photon Management

Effect of 3,4,9,10-Perylenetetracarboxylic Bisbenzimidazole (ptcbi) As Well As Bathocuproine (bcp) and Ag Interlayer Thickness on the Performance of Organic Tandem Solar Cells

Device Modeling of Efficient PBDB-T:PZT-Based All-Polymer Solar Cell: Role of Band Alignment

Morphology and Performance of Polymer Solar Cell Characterized by DPD Simulation and Graph Theory

Performance improvement of polymer solar cells with binary additives induced morphology optimization and interface modification simultaneously

Design and Optimization of High Performance P3HT: PCBM Polymer Solar Cell Using P3HT Buffer Layer

High-performance inverted polymer solar cells: Device characterization, optical modeling, and hole-transporting modifications

Performance enhancement in organic solar cells and photodetectors enabled by donor phase optimization at the surface of hole transport layer

Thickness Optimization of Front and Recombination ITO in Monolithic Perovskite/Silicon Tandem Solar Cells

Current or Power Matching? A Third Option for Monolithic All-Perovskite Tandem Solar Cells

Improved Performance of Small Molecule Solar Cell by Using Oblique Deposition Technique and Zinc Phthalocyanine Cathode Buffer Layer

Performance Optimization of Monolithic All-Perovskite Tandem Solar Cells under Standard and Real-World Solar Spectra

Performance optimization of homojunction perovskite solar cells by numerical simulation

Design of high efficiency perovskite solar cells based on inorganic and organic undoped double hole layer

OPTIMIZATION OF THE PEROVSKITE SOLAR CELL STRUCTURE

Effect of Electron Collecting Metal Oxide Layer in Normal and Inverted Structure Polymer Solar Cells

Performance Enhancement of Organic Solar Cells by Adding a Liquid Crystalline Molecule in Cathode and Anode Interlayers