Abstract:The work deals with the influence of the reach of the applied tool holder on the edge wear, dimensional accuracy and surface quality defined by the topography as well as the roughness of the machined surface. The research has been conducted on specimens made of Inconel 718 in the configuration of sleeves, within the scope of finish turning with constant cutting parameters, vc = 85 m/min; f = 0.14 mm/rev; ap = 0.2 mm. The material under machining has undergone heat treatment procedures such as solution treatment and precipitation hardening, resulting in a hardness of 45 ± 2 HRC. Two kinds of turning holders have been used with the reaches of 120 mm and 700 mm. The tools are intended for turning external and internal surfaces, respectively. The tests have been conducted using V-shaped cutting inserts manufactured by different producers, made of fine-grained carbide with coatings applied by the PVD (Physical Vapour Deposition) and CVD (Chemical Vapour Deposition) methods. The edge wear has been evaluated. The value of the achieved diameter dimensions has also been assessed in relation to the set ones, as well as the recorded values of surface roughness and the surface topography parameters have also been assessed. It has been determined that the quality of the manufactured surface evaluated by the 2D and 3D roughness parameters, as well as the dimensional quality are influenced by the kind of the applied tool holder. The influence is also visible considering the edge wear. The smallest values of the deviations from the nominal dimensions have been obtained for the coated inserts of the range of higher abrasion resistance (taking into account information from the producers). The obtained results show that in predicting the dimensional accuracy in the process of turning Inconel 718 alloy with long-overhang tools, one should consider the necessity of correction of the tool path. Taking into account the achieved surface roughness, it should be pointed out that not only the kind of the tool coating but also the character of its wear has a great influence, particularly, when a long cutting distance is required.

Control of Hot Bending Accuracy and Surface Quality for Inconel718 Thick Plate with Gradual Changed Curvature

Accuracy Control of Hot Bending for Inconel 718 Superalloy Thick Plate

Failure control on hydroforming process of thin-walled aluminum alloy with complex surface covers

Surface quality control method for 90° bending products in progressive die

The Finite Element Analysis for Dimensional Accuracy in Roll Bending of Aluminum-Polymer Laminated Sheet

Numerical and experimental study on in-plane bending of microchannel aluminum flat tube

Wrinkle Analysis and Control of Tube Bending for Hydroforming

Influence of bending angle function on local thinning defects of roll-formed sheets based on segmental boundary combination optimization

Springback Behavior and Control Strategy for Dimensional Accuracy of Hydroformed Tubular Parts

A novel cold expansion process for improving the surface integrity and fatigue life of small-deep holes in Inconel 718 superalloys

Evaluation of the Influence of the Tool Set Overhang on the Tool Wear and Surface Quality in the Process of Finish Turning of the Inconel 718 Alloy

Influence of process parameters on the flow forming quality of thin-walled tube with large diameter-thickness ratio

Prediction of Hot Deformation Behaviors Under Multiaxial Loading Using Gurson-Tvergaard-Needleman Damage Model for Inconel 718 Alloy Thin Sheet

The Influence of Σ3 Grain Boundary and Δ Phase Competition Mechanisms on Size Dependence and Micro-Deformation Behavior of Inconel 718 Foil

Bending analysis and control of rolled plate during snake hot rolling

Effect of Flexible 3D Multipoint Stretch Bending Dies on the Shape Accuracy and the Optimal Design

Process parameters optimization of differential heating push-bending for small bending radius tube based on orthogonal experiments

Mould Correction for Sheet-Metal Multi-Step Incremental Air-Bending Forming Based on Close-Loop Control and FEM Simulation

Deformation Optimization for Inconel718 Superalloy Sheet Hydroforming Numerically and Experimentally

Tc4 Deep Cylinder with Uniform Thickness by Friction-Changing Direct-Reverse Superplastic Forming

Effect of die structure parameters on deformation behavior of bent tube in free bending process