Abstract:To optimize the adhesion of layers presenting strong barrier properties on low-density polyethylene (LDPE) surfaces, we investigated the influence of argon and argon-oxygen atmospheric pressure post-discharges. This study was performed using x-ray photoelectron spectroscopy, atomic force microscopy, optical emission spectroscopy (OES) and dynamic water contact angle (WCA) measurements. After the plasma treatment, a slight increase in the roughness was emphasized, more particularly for the samples treated in a post-discharge supplied in oxygen. Measurements of the surface roughness and of the oxygen surface concentration suggested the competition of two processes playing a role on the surface hydrophilicity and occurring during the post-discharge treatment: the etching and the activation of the surface. The etching rate was estimated to about 2.7 nm.s-1 and 5.8 nm.s-1 for Ar and Ar-O2 post-discharges, respectively. The mechanisms underlying this etching were investigated through experiments, in which we discuss the influence of the O2 flow rate and the distance (gap) separating the plasma torch from the LDPE surface located downstream. O atoms and NO molecules (emitting in the UV range) detected by OES seem to be good candidates to explain the etching process. An ageing study is also presented to evidence the stability of the treated surfaces over 60 days. After 60 days of storage, we showed that whatever the O2 flow rate, the treated films registered a loss of their hydrophilic state since their WCA increased towards a common threshold of 80{\textdegree}. This 'hydrophobic recovery' effect was mostly attributed to the reorientation of induced polar chemical groups into the bulk of the material. Indeed, the relative concentrations of the carbonyl and carboxyl groups at the surface decreased with the storage time and seemed to reach a plateau after 30 days.

Surface Modification of Polyethylene (pe) Films Using Dielectric Barrier Discharge Plasma at Atmospheric Pressure

Study on the Surface Energy of HDPE Functionalizied Through Ultraviolet Light Irradiation

Surface Treatment of Polyethylene Terephthalate Films Using Dbd Excited by Repetitive Unipolar Nanosecond Pulses in Air at Atmospheric Pressure

Surface Treatment of PET and PP by Atmospheric Pressure Dielectric Barrier Discharge for Improvement in Hydrophilicity

Polypropylene Surface Plasma Modification Using Middle Frequency Power Supply

Experimental Study of Accelerating Surface Charge Dissipation on Polymer Treated by Repetitively Pulsed Discharge Plasmas

Surface Treatment of Polypropylene Films Using Dielectric Barrier Discharge with Magnetic Field

Study on Polypropylene Modified by Water Electrode Air Plasma

Study of Polypropylene Surface Modified by Dielectric Barrier Discharge

Polypropylene Surface Modification Model in Atmospheric Pressure Dielectric Barrier Discharge

Low-density polyethylene films treated by an atmospheric Ar--O2 post-discharge: functionalization, etching, degradation and partial recovery of the native wettability state

Improved Surface Modification of Polymer Films by Energy-Compressed Dielectric Barrier Discharge with Discharge-Time-Regulated Power Source

Surface Modification of Poly(tetrafluoroethylene) Films Via Plasma Treatment and Graft Copolymerization of Acrylic Acid

Surface Modification of Polytetrafluoroethylene by Microwave Plasma Treatment of H2O/Ar Mixture at Low Pressure

Surface Modification of Polyimide Films Using Unipolar Nanosecond-Pulse DBD in Atmospheric Air

Study on Polystyrene Surface Modification in Dielectric Barrier Discharge

Dielectric barrier discharge plasma treatment of ultrahigh molecular weight polyethylene in different discharge atmospheres at medium pressure: A cell-biomaterial interface study

Modification of surface properties of polypropylene (PP) film using DC glow discharge air plasma

A low power 50 Hz argon plasma for surface modification of polytetrafluoroethylene

Investigation on gas plasma and liquid plasma treatment for polyether ether ketone (PEEK) surface for wettability enhancement

Treatment of Polymeric Films Used for Printed Electronic Circuits Using Ambient Air DBD Non-Thermal Plasma