Abstract:Polyurethane foam (PUF) is one of the most well-known cellular materials and is widely employed in various industrial and biomedical fields thanks to its many advantages. These include mechanical and material characteristics such as low density and thermal conductivity, and high specific elastic modulus and strength. Despite of these advantages, the PUF has extremely complex material nonlinearity, with changes in density and strain rate, which is a major obstacle to material design and the application of PUF-based structures. PUF has elasto-viscoplastic behavior including three stages of material features, linear elasticity, softening/plateau with stress drop and densification. These phenomena depend strongly on strain rate and density. Therefore, in this study, a phenomenological constitutive model, namely, an elasto-viscoplastic model, was proposed to describe the density- and strain rate-dependent material nonlinear behavior of PUF. The yield surface-independent plastic multiplier, and the hardening- and softening-associated internal state variables proposed by Frank and Brockman, and Zairi et al. were adopted in the constitutive model, respectively. The proposed constitutive model was discretized using the implicit time integration algorithm and was implemented into a user-defined subroutine of the commercial finite element analysis program, ABAQUS. At the same time, a deterministic identification method for material parameters of the constitutive model was introduced to predict the precise material response of PUF under arbitrary densities and strain rates. To do this, the three-dimensional constitutive model was contracted to a one-dimensional equation, and the explicit equation for each material parameter was derived. Then, the strain hardening- and softeningdependent material parameters were calculated using experimental results, such as the work hardening ratestress curve and the yield stress-strain rate curve. After analyzing the obtained material parameters, it was found that the material parameters were strongly dependent on the density and the strain rate. Consequently, the macroscopic material response of PUF, such as a uniaxial compressive stress-strain curve, can be predicted based on the proposed method in this study.

Characterisation and modelling of a transversely isotropic melt-extruded low-density polyethylene closed cell foam under uniaxial compression

Characterisation and Modelling of A Melt-Extruded Ldpe Closed Cell Foam

Mechanical Performance of Polystyrene Foam (EPS): Experimental and Numerical Analysis

Impact Properties of Uniaxially Thermoformed Auxetic Foams

Topological Characteristics and Mechanical Properties of Uniaxially Thermoformed Auxetic Foam

Morphology and Compressive Properties of Extruded Polyethylene Terephthalate Foam

A New Method for the Dynamics Analysis of Super-Elastic-Plastic Foams under Inhomogeneous Loading and Unloading Conditions

Crushing and Densification of Rapid Prototyping Polylactide Foam: Meso-structural Effect and a Statistical Constitutive Model

A phenomenological constitutive modelling of polyethylene foam under multiple impact conditions

Constitutive modeling of the viscoelastic mechanical response of foam rubber-like materials

Modelling hollow thermoplastic syntactic foams under high-strain compressive loading

A Three-Dimensional Thermal Model for Viscoelastic Polymer Melt Packing Process in Injection Molding

Crushing of a closed-cell polymeric foam under triaxial loading

Comprehensive analysis of mechanical properties of microcellular polypropylene: Experiment and simulation

Dynamic Compression Characteristics of Polystyrene Foam Materials

Study of the Constitutive Relation of Low Density Plyethylene Foam under Compression

Experimental approach for characterizing the nonlinear, time and temperature‐dependent constitutive response of open‐cell polyurethane foams

Investigation of Density- and Strain Rate-dependent Strain Hardening-softening-coupled material Behavior of Polyurethane Foams using Elasto-viscoplastic Constitutive Model

Experimental and Analytical Study on the Compressive Behavior of PMI Foam with Different Densities and Cell Sizes under Intermediate Strain Rates

High fidelity simulation of the mechanical behavior of closed-cell polyurethane foams

Characterization and modeling of the uniaxial thermo-mechanical compressive behavior of polymethacrylimide (PMI) foam at different temperatures