Abstract:Water-powered projectile-assisted injection molding (W-PAIM) is a novel injection molding technology that has been recently developed based on the ripe water-assisted injection molding (WAIM). Fiber orientation pattern and residual wall thickness (RWT) are two crucial factors determining the quality of W-PAIM parts composed of short fiber-reinforced thermoplastics (SFRTCs). However, limited work has been conducted on W-PAIM of SFRTC parts, which restricts its application process. In this work, an intensive investigation of W-PAIM parts composed of short fiber-reinforced polypropylene was conducted via a newly lab-developed W-PAIM platform. The results indicated that fibers were quite well oriented in the region extending from the core zone to the water channel, especially in the water channel zone, but randomly aligned in a small region near the mold wall. Nevertheless, fibers in the water channel zone of W-PAIM part were highly oriented, presenting an opposite alignment trend in fiber orientation compared to that in the water channel zone of the WAIM part as reported earlier. These disparities in fiber orientation between W-PAIM and WAIM parts were primarily attributed to the strong flow fields generated by projectile penetration. Additionally, the influence of three main processing parameters that significantly affected the projectile penetration on these two crucial factors was also investigated using the single-factor method. It was discovered that water injection delay time constituted the primary factor affecting the projectile penetration process, and reducing this time could greatly increase the relative thickness of the ordered area and the uniformity of RWT. More importantly, within the value range of the tested processing parameters, increased water pressure, elevated melt temperatures, and shorter water injection delay time could simultaneously improve fiber orientation and the uniformity of RWT in W-PAIM parts, which may improve the properties of W-PAIM parts and enlarge their application scope. This work provides a comprehensive guide for the fabrication of W-PAIM parts of SFRTCs.

Residual Wall Thickness Study of Variable Cross-Section Tube in Water-Assisted Injection Molding

Simulation and Experimental Analysis on Non-circular Cross-section Parts Residual Wall Thickness of Water-assisted Injection Molding

Effect on Residual Wall Thickness of Parts with Floating Core Injection of Water-Assisted Injection Molding

Numerical Simulation on Residual Wall Thickness of Tubes with Dimensional Transitions and Curved Sections in Water-Assisted Injection Molding

Numerical analysis of process parameters influencing residual wall thickness in water-assisted injection molding

Model and Simulation of Water Penetration in Water-Assisted Injection Molding

Study of Residual Wall Thickness and Multiobjective Optimization for Process Parameters of Water-Assisted Injection Molding

ANALYSIS OF LOAD CHARACTERISTICS AND CONTROL OF WATER HYDRAULIC SYSTEM FOR WAIM

Experimental and numerical investigations on formation mechanisms of hollow structures in overflow water‐assisted injection‐molded parts of short‐glass‐fiber‐reinforced polypropylene

Applications of Water-Assisted Injection Molding on Front Fork of Bicycle

Numerical Simulation on the Penetration Behavior of the Projectile during the Water Injection Stage of Water-Projectile-Assisted Injection Molding Process

Study of Water Penetration Length and Processing Parameters Optimization in Water-Assisted Injection Molding

Experimental analysis of fluid‐assisted injection molding of pipe fittings with different angles by short‐shot method

Simulation and Experiment Research on the Proportional Pressure Control of Water-Assisted Injection Molding

Shrinkage and Warpage Mechanism of Overflow Water-Assisted Injection Molding Short Fiber-Reinforced Polymers

The Investigation of Overflow Water-Powered Projectile-Assisted Injection Molded Short-Glass-Fiber-Reinforced Polypropylene

Numerical and experimental investigations on the mechanism of flow‐induced fiber orientation in short‐shot water‐assisted injection‐molded short‐glass‐fiber‐reinforced polypropylene

Research of Water Assisted Injection Molding Technology

The study of short‐shot water‐assisted injection molding of short glass fiber reinforced polypropylene

Experimental and Numerical Analysis on Core Deflection During Wax Injection

Influence of Processing Conditions on the Morphological Structure and Ductility of Water-Foamed Injection Molded PP/LDPE Blended Parts