Abstract:The effect of solo and combined addition of Al (3wt. %) and Zn (1wt. %) into gravity-cast Mg-10 wt. % Sn binary alloy on the dry sliding wear test has been investigated using pin-on-disk configuration with varying rotational speed (100 and 200 rpm) under a range of test loads (10, 20, 30, and 40 N). Microstructural characterization and phase analysis of the as-cast Mg-Sn alloys using scanning electron microscope and x-ray diffraction, respectively, have revealed the refinement of the binary alloy microstructure in terms of smaller dendritic arm spacing, uniform and discrete distribution of eutectic phase mixture at the interdendritic locations owing to the alloying additions. Moreover, a significant improvement in microhardness is achieved with increase in amount (wt.%) of alloying elements, depicting the highest hardness in the Mg-10Sn-3Al-1Zn (wt.%) alloy. Simultaneously, the alloying addition even in micro-concentration has been found to reduce the specific wear rate than that of the binary alloy over the entire loading range. The post-wear topographical surface features and chemical analysis using scanning electron microscope and energy-dispersive x-ray spectroscopy of the investigated alloys have suggested the oxidation and abrasion as dominant wear mechanisms. The reduced wear rates in the Al containing alloys are ascribed to the protective and continuous mechanically mixed oxide scale formation during test, which acts as a lubricating layer between the pin and the rotating disk. The discrete oxide island formation at the Zn-lean regions of Zn containing alloys is responsible for their accelerated wear rates.

Promoting the High Load-Carrying Capability of Al–20 Wt%sn Bearing Alloys Through Creating Nanocomposite Structure by Mechanical Alloying

Microstructure and Wear Properties of Al-Based Bearing Alloys Fabricated by Mechanical Alloying

Wear Behavior of Al–Sn Alloys with Different Distribution of Sn Dispersoids Manipulated by Mechanical Alloying and Sintering

A remarkable enhancement of mechanical and wear properties by creating a dual-scale structure in an Al–Sn–Si alloy

Enhancement of Wear Properties of Ultrafine-Structured Al–Sn Alloy-Embedded Sn Nanoparticles Through in Situ Synthesis

Dry sliding wear of MA/PM Al-10Ti alloy

Improving wear performance of dual-scale Al–Sn alloys by adding nano-Si@Sn: Effects of Sn nanophase lubrication and nano-Si polishing

Significant Improvement of Wear Properties by Creating Micro/nano Dual-Scale Structure in Al–Sn Alloys

Microstructure and wear properties of nanocomposite Al-Pb-Cu alloy cold-rolled onto steel matrix

Effect of Alloying Elements on the Dry Sliding Wear Characteristics of Gravity-Cast Mg-Sn Based Alloys

Study on synthesis and structure of mechanically alloyed W-Ni-Fe nanocomposite powders

Microstructure and Wear Properties of Al–Pb–Cu Alloys Prepared by Mechanical Alloying

Microstructure and Morphology of Al-Pb Bearing Alloy Synthesized by Mechanical Alloying and Hot Extrusion

Improvement of the Wear Behaviour of Al–Pb Alloys by Mechanical Alloying

Formation of nanocrystalline and amorphous phase of Al-Pb-Si-Sn-Cu powder during mechanical alloying

Improving Wear Performance of Dual-Scale Al–Sn Alloys: the Role of Mg Addition in Enhancing Sn Distribution and Tribolayer Stability

Synergetic Enhancements on the Mechanical and Tribological Performance of Al10Cr17Fe20NiV4 Medium‐Entropy Alloys Induced by Nano‐Al2O3 Particles

Effect of Fe and Mn additions on microstructure and wear properties of spray-deposited Al–20Si alloy

Melting Behavior and the Correlation of Sn Distribution on Hardness in a Nanostructured Al–Sn Alloy

MICROSTRUCTURE AND WEAR PROPERTIES OF Al-Pb-Cu ALLOY SYNTHESIZED BY MECHANICALLY ALLOYING

Preparation of Cbnp/Nicral Nanostructured Composite Powders by A Step-Fashion Mechanical Alloying Process