Abstract:In the current study, a 3-D microscopic structural finite element (FE) model of interpenetrating SiC/Al composites (SiC/Al IPCs) is built, based on X-ray tomography and optimized methods for 3-D mesh generation. In addition, an interface model is introduced into the 3-D FE model to investigate the effects of the interfaces on the damage and failure processes, which includes a “tie-break contact” method at the SiC/Al interfaces. Subsequently, FE methods are applied to investigate the dynamic compression response of the 3-D FE model. To validate the numerical simulation results, the dynamic compression responses of SiC/Al IPCs are measured at strain rates of 2000s−1 using a split Hopkinson pressure bar device. Our results show that failure of the SiC phase occurs just before the effective stress reaches its peak, but it plays a leading role in bearing the pre-metaphase stage of the load. From the point of energy dissipation, however, the contribution of Al phase cannot be ignored in the final stage of failure because the residual Al phase absorbs 30% of the energy of the global model by plastic deformation, even though its mass failure ratio is only 2%. Further microanalysis shows that the cracks initiate and propagate mainly near the SiC/Al interface, just on the side of the SiC ceramic phase. As the cracks extend further into the SiC phase, there appears a new “interface debonding” failure mode. These results show that brittle fracture of the SiC ceramic phase plays a key role in crack initiation, since the presence of complex 3-D SiC/Al interfaces usually causes the generated cracks to deflect before interconnecting with each other. This significantly retards propagation of the cracks, and thus increases the ductility of the composite materials. In the final stage of failure, the cracks are interconnected with each other in the SiC phase while the Al phase still maintains a degree of structural integrity. It is found that there exists obvious plastic deformation in local, relatively narrow, regions in the Al phase, and the local necking and tearing fractures tend to be localized in these severely deformed regions. Numerical simulation results are consistent with the observed behavior.

Damage Evolution of the Interphase on C/SiC Composites with CZM Method

Application and Analysis of Plane Woven C/Sic Composites Based on Continuum Damage Mechanics

A Molecular Dynamics Based Cohesive Zone Model for Interface Failure under Monotonic Tension of 3D Four Direction SiCf/SiC Composites

Damage Theoretical Analysis of 2.5D C/SiC Composites under Tensile and Shear Loading

Damage Evolution and Fracture Behavior of C/SiC Minicomposites with Different Interphases under Uniaxial Tensile Load

Stress Field and Damage Evolution in C/SiC Woven Composites: Image-Based Finite Element Analysis and in Situ X-Ray Computed Tomography Tests

APPLICATION AND THEORETICAL ANALYSIS OF C/SiC COMPOSITES BASED ON CONTINUUM DAMAGE MECHANICS

An Efficient Multi-Scale Method for Failure Mechanism Analysis of SiCf/Ti Composites with Experimental Validation

Simulation of Damage and Failure Processes of Interpenetrating SiC/Al Composites Subjected to Dynamic Compressive Loading

Effect of thermal residual stress on the tensile properties and damage process of C/SiC composites at high temperatures

Numerical Simulation of Thermal Residual Stresses For Unidirectional C/SiC Composites

Development and validation of an anisotropic damage constitutive model for C/SiC composite

A CDM Model and its FE Implementation for 2D C/SiC Composite under Tension and Shear Loads

Influence of Interphase Type and Thickness on the Interface Properties and Tensile Damage Evolution of C/SiC Composites

A novel phase‐field based cohesive zone model for modeling interfacial failure in composites

Micromechanical Analysis of SiC/Ti6Al4V Composite Under Complex Stress State

Experimental and numerical studies on low-velocity impact of laminated C/SiC structures

Internal Damage Evolution Investigation of C/SiC Composites Using In-Situ Tensile X-ray Computed Tomography Testing and Digital Volume Correlation at 1000 °C

Investigation on crack propagation of SiCf/SiC composite via PF-CZM method

Damage Characteristics and Constitutive Modeling of the 2D C/SiC Composite: Part II – Material Model and Numerical Implementation

Cross-scale Static/dynamic Shear Damage Evolution Mechanism of 2D C/SiC Ceramic Matrix Composite with Transient Hysteresis Effect