Abstract:Direct conversion receiver (DCR) architecture is a promising candidate in the radio frequency (RF) front end because of its low power consumption, low cost and ease of integration. However, flicker noise and direct current (DC) offset are large issues. Owing to the local oscillator (LO) frequency, which is half of the RF frequency, and the absence of a DC bias current that introduces no flicker noise, the subharmonic passive mixer (SHPM) core topology front end overcomes the shortcoming effectively. When more and more receivers (RX) and transmitters (TX) are integrated into one chip, the linearity of the receiver front end becomes a very important performer that handles the TX and RX feedthrough. Another reason for the requirement of good linearity is the massive electromagnetic interference that exists in the atmosphere. This paper presents a linearity-improved RF front end with a feedforward body bias (FBB) subharmonic mixer core topology that satisfies modern RF front end demands. A novel complementary derivative superposition (DS) method is presented in low noise amplifier (LNA) design to cancel both the third- and second-order nonlinearities. To the best knowledge of the authors, this is the first time FBB technology is used in the SHPM core to improve linearity. A Volterra series is introduced to provide an analytical formula for the FBB of the SHPM core. The design was fabricated in a 0.13 μm complementary metal oxide semiconductor (CMOS) process with a chip area of 750 μm × 1270 μm. At a 2.4 GHz working frequency, the measurement result shows a conversion gain of 36 dB, double side band (DSB) noise figure (NF) of 6.8 dB, third-order intermodulation intercept point (IIP3) of 2 dBm, LO–RF isolation of 90 dB and 0.8 mW DC offset with 14.4 mW power consumption at 1.2 V supply voltage. These results exhibit better LO–RF feedthrough and DC offset, good gain and NF, moderate IIP3 and the highest figure of merit compared to the state-of-the-art publications.

A High Dynamic Range Linear Rf Power Detector with A Preceding Lna

A 25-31Ghz Compact True Power Detector with >33db Dynamic Range in 40nm Bulk CMOS

High-Linearity Direct Conversion Receiver with the Transconductance Equalization Technique and DCOC Method

A Sub-GHz Low-Power Receiver Employing Resistive-Feedback-Tuned LNA with 2.1-Db NF and 106-Db Gain Tuning Range

A Sub-GHz CMOS Low-IF Receiver for Lot Applications

A Highly Linear 2.4GHz Low Noise Amplifier

A Sub-1-GHz Band High-Dynamic-Range Receiver with Integrated Self-Adaptive Multipart AGC Loops

A High Linearity Class AB Power Amplifier for Sub-1 GHz Applications

A High-Linearity 7–9-Ghz Receiver Front End with Strength-Oriented Nonlinearity Cancellation

An Effective DC Offset Calibration Method Combined with Analog and Digital Circuits for Direct Conversion Receivers

A Low-Power Low-Noise Direct-Conversion Front-End with Digitally Assisted IIP2 Background Self Calibration

A High Performance 2-Ghz Direct-Conversion Front End with Single-Ended RF Input in 0.13 Um CMOS

A wide band CMOS radio frequency RMS power detector with 42-dB dynamic range

A Reverse-RSSI Logarithmic Power Detector With +35-dBm Maximum Detectable Power in 180-nm CMOS

A 900 MHz,21 Dbm CMOS Linear Power Amplifier with 35% PAE for RFID Readers

A dual band CMOS two-stage variable gain low noise amplifier

A Linearity Improvement Front End with Subharmonic Current Commutating Passive Mixer for 2.4 GHz Direct Conversion Receiver in 0.13 Μm CMOS Technology

A Mobile UHF RFID Reader with High Linearity Receiver

Low Power Low Noise Amplifier with DC Offset Correction at 1 V Supply Voltage for Ultrasound Imaging Systems

A 5 Ghz 7.2 Db Nf Low Power Direct Conversion Receiver Front-End with Balun Lna

A Novel Low-Noise High-Linearity CMOS Transmitter for Mobile UHF RFID Reader