Abstract:The flow condensation heat transfer coefficient of R134a inside two helical micro-fin tubes with outer diameter of 6.35 mm and helical angles of 18o and 28o respectively were experimentally studied at a high mass flux ranging from 500 to 1100 kg m−2 s−1. The condensation temperatures are 35°C, 40°C and 45°C, and the vapor qualities ranges from 0.95 to 1.00 at the inlet section and from 0.00 to 0.05 at the outlet section. Experimental results show that there are annular and intermittent flow regimes inside the tube under experimental conditions, the ratio of annular flow region to the total heat transfer region is about 70%. The liquid film flow changes from rotational flow to coexistence of rotational and horizontal flows when the vapor quality is 0.475±0.08, 0.486±0.06 and 0.521±0.05, respectively and the corresponding saturation temperature is 35°C, 40°C and 45°C. Based on the experimental data, the heat transfer coefficient increases with increasing mass flux and fin helical angle, and with decreasing saturation temperature and Reynolds number of cooling water. In addition, the heat transfer coefficient of annular flow is greater than that of intermittent flow, in other words, the heat transfer coefficient increases with increasing vapor quality. The heat transfer coefficient obtained at high mass flux was compared with the calculated data of some published correlations used at low mass flux. It was found that most correlations underestimate the experimental heat transfer coefficient inside the micro-fin tube, and these prediction deviation increases with increasing mass flux and fin helical angle. By introducing some dimensionless numbers as well as considering the flow mechanism of liquid film inside the tube, two heat transfer coefficient correlations were proposed based on the experimental data. The ratio of liquid film thickness to fin height was used to characterize whether the liquid film flow is rotational flow or coexistence of rotational and horizontal flows in the proposed correlation, which shows a better prediction accuracy with a mean deviation of less than 7.3%.

An Innovative Method for Prediction of Liquid Metal Heat Transfer Rate for Rod Bundles Based on Annuli

Theoretical Analysis of Heat Transfer for Liquid Metal Through Tube Bundles

Investigation on heat split in a vertical 3 × 3 dual-cooled annular rod bundle

Mhd Effect on Flow Structures and Heat Transfer Characteristics of Liquid Metal-Gas Annular Flow in A Vertical Pipe

Convective Heat Transfer Coefficient for a Rod-Like Particle in a Uniform Flow

Investigation on the Applicability of Turbulent-Prandtl-Number Models in Bare Rod Bundles for Heavy Liquid Metals

Simulation of Turbulent Flow and Heat Transfer in Channels Between Rod Bundles

Numerical Investigation of Thermal-Hydraulic Behaviors in a LBE-cooled 19-Pin Wire-Wrapped Rod Bundle

Study on the Prediction of DNB-Type Critical Heat Flux in Rod Bundle Under Motion Conditions

Numerical and Experimental Analysis of LBE Flow and Heat Transfer Characteristics in Hexagonal Rod Bundles

Experimental Study of Condensation Heat Transfer of R134a Inside the Micro-Fin Tubes at High Mass Flux

Experimental Study on Flow Split and Pressure Drop Characteristics in a 3 × 3 Dual-Cooled Annular Rod Bundle

Numerical Investigation on Heat Transfer Characteristics of Liquid Metal Cross Flow over Tube Bundles

Research on prediction of non-uniform heated rod bundle CHF based on subchannel analysis code coupling modified mechanistic model

New Models of Droplet Deposition and Entrainment for Prediction of Liquid Film Flow in Vertical Annuli

Evaluation of Prediction Methods for Heat Transfer Coefficient of Annular Flow and a Novel Correlation

Numerical Investigation for the Heat Transfer Mechanisms Between Subchannels of Bar Rod Bundles Cooled by Liquid Sodium

Prediction of Critical Heat Flux in Non-Uniform Heated Rod Bundle Based on Modified CHF Empirical Correlations

Flow and Heat Transfer Characteristics of Liquid Metal Sodium in Tubes with Different Inner Wall Structures

A Correlation Of Heat Transfer Non-Uniformity In Rod Bundle And Its Application To Sub-Channel Code

An Experiment Study of Pressure Drop and Flow Distribution in Subchannels of a 37-Pin Wire-Wrapped Rod Bundle