Abstract:The stacking sequences of fiber-reinforced composites for optimization of turbine blades with the best performance have become a focus of attention. However, the optimization and design principles of its flexural performance are not yet mature. Referring to the problems in previous work, a 3D finite element flexural model of carbon fiber reinforced composites was established based on the Abaqus/Explicit VUMAT subroutine through the Tsai-Wu failure criterion. The influencing laws and optimization mechanisms of different stacking patterns (e.g., different orientations, number of orientation plies, combination of multiple orientation plies, and symmetry/asymmetry structures) on the flexural properties of the composites were systematically investigated, and corresponding design references for the optimization of stacking patterns were given. The results show that the smaller the value of ∣θ−45°∣ (θ represents the angle of the orientation ply), the more obvious the stress reduction of the orientation ply, and the orientation ply located in the outer layer is more conducive to the improvement of flexural performance. As the number of orientation plies increases, the flexural strength and displacement increase, but the stability decreases, in which the laminate with 50 % 0° orientation plies has the best overall performance. In addition, the stability ranking of the laminate stacking sequences for the same 0° orientation ply proportion is: multi-orientation asymmetric > multi-orientation symmetric > single-orientation symmetric. In particular, the [75/02/60/30/02/15] laminate has the best overall performance with the flexural strength of 974 MPa and the Y-axis offset of 0.057 mm, and its stability is 66 % higher than that of the [15/02/75]S laminate. Under the same tensile/compressive stresses, the actual stress of the warp/weft in the orientation ply is less than the maximum ideal stress and the stress of Y-axis direction SY ≠ 0, which delays the fracture of the orientation ply and causes displacement offset, and the increase of the number of orientation plies will aggravate this effect. The obtained highlighted results can provide valuable references for the design and optimization of stacking patterns of plain fabric-reinforced laminates with high flexural properties.

Effects of Layer Stacking Sequence on Temperature Response of Multi-Layer Composite Materials under Dynamic Conditions

Transient Thermal Response of a Multilayered Geomaterial Subjected to a Heat Source

Thermal responses of layered pavement system with unsteady heat conduction

Response of Dynamic Interlaminar Stresses in Laminated Plates under Free Vibration and Thermal Load

Effects of Stacking Sequence on Thermal Flutter Speed of Composite Panel

Numerical Analysis on Thermal Stress of Multilayer Materials Combined Structures for a Lightweight Thermal Protection System

Numerical investigation of the effect of thermal gradients on curing performance of autoclaved laminates

Mechanical properties and failure mechanisms of composite laminates with classical fabric stacking patterns

Coupled machine-learning approach and thermoelasticity for analyzing thermal stability of the nanocomposite sandwich system

Transient Thermomechanical Responses of Multilayered Viscoelastic Composite Structure with Non-Idealized Interfacial Conditions in the Context of Generalized Thermoviscoelasticity Theory with Time-Fractional Order Strain

Mechanical behavior in bending deformation of thermoplastic composite laminates with different stacking sequences

Hygrothermal Effect on Dynamic Interlaminar Stresses in Laminated Plates with Piezoelectric Actuators

Effect of Temperature on the Compressive Behavior of Carbon Fiber Composite Pyramidal Truss Cores Sandwich Panels with Reinforced Frames

On the Analysis of Temperatures, Surface Morphologies and Tool Wear in Drilling CFRP/Ti6Al4V Stacks under Different Cutting Sequence Strategies

Effect of different stacking sequences on hybrid carbon/glass/epoxy composites laminate: Thermal, dynamic mechanical and long-term behavior

An analytical study of transient thermo-viscoelastic responses of viscoelastic laminated sandwich composite structure for vibration control

Hygrothermal effects on translaminar fracture toughness of quasi-isotropic laminates with different stacking sequences

Dynamic Interlaminar Stresses in Laminated Plates with Piezoelectric Actuators in Thermal Environments

Numerical Investigation on the Design and Optimization of Stacking Pattern for High Flexural Performance Carbon Fiber Reinforced Resin Matrix Composites

New Insights on Piezoelectric Thermoelastic Coupling and Transient Thermo-Electromechanical Responses of Multi-Layered Piezoelectric Laminated Composite Structure

Thermal analysis for laminated plates with arbitrary supports under non-uniform temperature boundary conditions