Abstract:Conventional thixoforming technology had advantages of casting and forging, but low plastic deformation degree and existence of liquid phase lowered the mechanical property. In this work, 6A02 bracket-shape component was firstly manufactured by the efficient thixoforming-forging compound forming technology and bimodal semisolid billet. Bimodal semisolid feedstock was beneficial for both filling ability and mechanical strength due to intragranular dislocation and elongated grain shape. Firstly, a Deform-3D simulation of compound forming was established by controlling temperature field distribution. Then the effects of billet shapes, billet temperatures, soaking times, mold temperatures and dwell times on microstructures and mechanical properties were investigated. Though the mechanical strength and ductility at the shoulder were elevated by larger plastic deformation in the integrated forming process, they were still lower than those at side wall and bottom part in virtue of liquid segregation. Besides, the largest yield strength σ y , tensile strength σ max and elongation δ of compound-formed 6A02 components were even 16.8%, 25.8%, and 77.6% higher than σ y , σ max and δ of 6A02 hot-extruded bar, respectively. Finally, the deformation behavior and strengthening mechanism of compound forming technology were discussed deeply. Particularly, except liquid fraction, deformation behavior was relevant with grain size and morphology. For rounder and smaller grains, grain boundary sliding was dominant. But slip deformation was predominant for large-deformed grains. Subsequently, a new dynamic recrystallization (DRX) mechanism was proposed and only continuous dynamic recrystallization (CDRX) could make the wet grain boundary serrated. A quantitative insight into strengthening mechanism indicated that solid solution strengthening and dislocation strengthening were dominant. This study provided a theoretical guidance and experimental support for the efficient application and forming control of 6A02 alloy in compound forming area.

Superplastic forming Ti-6Al-4V titanium alloy cylinder with near uniform thickness distribution

Investigation on the Factors Influencing the Thickness Distribution of Superplastic-Formed Components

Hot Gas Pressure Forming of Ti-55 High Temperature Titanium Alloy Tubular Component

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

A Review on Superplastic Forming of Ti-6Al-4V Alloy

Thixoforming-forging compound forming technology for 6A02 Al bracket-shape component

High-efficiency forming processes for complex thin-walled titanium alloys components: state-of-the-art and perspectives

Superplastic Forming of a Three-Stage Hemispherical 5083 Aluminium Profile

Effect of Process Parameters and Layer Thickness on the Quality and Performance of Ti-6Al-4V Fabricated by Selective Laser Melting

Wrinkling and Strengthening Behaviors in the Two-Layer-Sheet Hot-Forming–Quenching Integrated Process for an Al–Cu–Mg-Alloy Thin-Walled Curved-Surface Shell

A Study of Titanium Alloy Integral Control Surface Based on Superplastic Forming/Diffusion Bonding

Change in geometry size and thinning rate in single-point incremental forming process of TA1 sheet: evaluation method and finite element analysis

Study on hydroforming of AA6061-T6 aluminum alloy sheet based on upper sheet

Casting Design Optimization Using Numerical Simulation of Precision Forging Die for Large Titanium Alloy Integral Bulkhead

Tailoring Titanium Sheet Metal Using Laser Metal Deposition to Improve Room Temperature Single-Point Incremental Forming

Process Development for a Superplastic Hot Tube Gas Forming Process of Titanium (Ti-3Al-2.5V) Hollow Profiles

Enhanced forming height and accuracy of thin-walled aluminum alloy by impact pneumatic forming

An Experimental and Simulation Study on the Formability of Commercial Pure Titanium Foil

Forming Behavior of Additively Manufactured Al/Ti Material Compounds Produced by Cold Spraying

Study on the organization and properties of Ti–6Al–4 V fabricated by laser powder bed fusion based on the thickness of the gradient layer