Abstract:This paper reports a grain regrowth and bifacial passivation strategy to reduce recombination losses for wide‐bandgap perovskite solar cells. As a result, PCEs of 21.9% and 19.9% are achieved for the opaque and semitransparent perovskite solar cells, respectively. Furthermore, a perovskite/silicon 4‐terminal (4‐T) tandem cell with an attractive PCE of 29.8% is realized. The wide‐bandgap perovskite solar cell is a crucial part of perovskite/silicon tandem solar cells, which offer an avenue for surpassing the power conversion efficiency (PCE) limit of single‐junction silicon solar cells. However, the actual efficiency of such tandem solar cells today is diminished by the nonradiative recombination losses in the wide‐bandgap perovskite subcells. Here, this work reports a grain regrowth and bifacial passivation (GRBP) strategy to reduce recombination losses at the grain boundaries and perovskite/charge transport layer interfaces simultaneously. This is achieved by a posttreatment of perovskite films with a mixture of methylammonium thiocyanate (MASCN) and phenethylammonium iodide (PEAI). The MASCN induces the regrowth of perovskite grains and simultaneously facilitates the penetration of PEAI into the hole‐transport‐layer (HTL)/perovskite bottom interface. Thereby, the bulk and interface nonradiative recombination losses are reduced and the open‐circuit voltage in solar cells is considerably increased. PCEs of 21.9% and 19.9% for the 1.65‐eV bandgap opaque and semitransparent perovskite solar cells, respectively, are obtained. The encapsulated semitransparent perovskite solar cells retain their initial efficiency following 500 h of operation under one‐sun illumination in ambient conditions. The perovskite/silicon 4‐terminal (4‐T) tandem cells are fabricated with impressive PCEs 29.8% and 28.5% for 0.049 cm2 and 1 cm2 devices, respectively.

Coherent growth of high-Miller-index facets enhances perovskite solar cells

A Polymerization‐Assisted Grain Growth Strategy for Efficient and Stable Perovskite Solar Cells

Polymer-templated nucleation and crystal growth of perovskite films for solar cells with efficiency greater than 21%

Material nucleation/growth competition tuning towards highly reproducible planar perovskite solar cells with efficiency exceeding 20%

Perovskite Monocrystals: Ultrathin Perovskite Monocrystals Boost the Solar Cell Performance (Adv. Energy Mater. 34/2020)

Homogeneous Grain Boundary Passivation in Wide‐Bandgap Perovskite Films Enables Fabrication of Monolithic Perovskite/Organic Tandem Solar Cells with over 21% Efficiency

A Thermotropic Liquid Crystal Enables Efficient and Stable Perovskite Solar Modules

Bulk Defect Suppression of Micrometer-Thick Perovskite Single Crystals Enables Stable Photovoltaics

Surface Reconstruction for Efficient and Stable Monolithic Perovskite/Silicon Tandem Solar Cells with Greatly Suppressed Residual Strain

Morphology Optimization of Perovskite Films for Efficient Cells and Modules through Solvent Engineering

In Situ Synthesized 2D Covalent Organic Framework Nanosheets Induce Growth of High‐Quality Perovskite Film for Efficient and Stable Solar Cells

High-efficiency solution-processed perovskite solar cells with millimeter-scale grains

Efficient micrometer-scale thick-film perovskite solar cells with superior stability

Crystal Growth Regulation of 2D/3D Perovskite Films for Solar Cells with Both High Efficiency and Stability

Epitaxial Growth of α‐FAPbI3 at a Well‐Matched Heterointerface for Efficient Perovskite Solar Cells and Solar Modules

Mesoporous PbI2 Assisted Growth of Large Perovskite Grains for Efficient Perovskite Solar Cells Based on ZnO Nanorods

Epitaxial 2D PbS Nanosheet‐Formamidinium Lead Triiodide Heterostructure Enabling High‐Performance Perovskite Solar Cells

Grain Regrowth and Bifacial Passivation for High‐Efficiency Wide‐Bandgap Perovskite Solar Cells

Modulating Crystal Growth of Formamidinium–caesium Perovskites for over 200 Cm2 Photovoltaic Sub-Modules

Heterogeneous Nucleation and Enhanced Charge Transfer via Amorphous Metal‐Organic Frameworks for Efficient and Stable Perovskite Solar Cells

Low-bandgap Mixed Tin–lead Iodide Perovskite with Large Grains for High Performance Solar Cells