Abstract:Organometal halide perovskite is one of the most promising materials for high efficient thin-film solar cell. Solution fabrication process shows that the recorded power conversion efficiency (PCE) is 23.7%, however, large scale fabrication suffers the inevitable toxic solvent, preventing it from implementing the green commercialization. As one of the matured large-scale fabrication techniques, the vapor deposition is recently found to promise the green fabrication of perovskite thin film without toxic solvent. However, the PCE based on vapor deposition is considerably lower than that based on solution fabrication because of ineffective regulation methods of the perovskite films. So, there is intensive requirement for optimizing the growth of perovskite in vapor deposition for improving PCE, especially, developing a kind of quality regulation method of the perovskite films. In this study, we provide a method of adjusting grain size in vapor deposition method. The grain size optimization of MAPbI 3 films is realized by simply modulating the reaction temperature between PbI 2 films and MAI vapor. We set the reaction temperature to be 140 °C, 160 °C, 180 °C and 200 °C separately and establish the relationship between reaction time and grain size during the complete conversion of PbI 2 film into MAPbI 3 film. We find that the average grain size of the film increases first with growth temperature increasing from 140 °C to 180 °C and then decrease at 200 °C, giving an average grain size of 0.81 \begin{document}${\text{μm}}$\end{document} and a largest grain size of about 2 \begin{document}${\text{μm}}$\end{document} at 180 °C. The defect density of perovskite film is deduced from the space charge limited current model, showing that it decreases from 5.90 × 10 16 cm –3 at 140 °C to 2.66 × 10 16 cm –3 at 180 °C. Photovoltaic devices with structure FTO/TiO 2 /C 60 /MAPbI 3 /spiro-OMeTAD/Au are fabricated to demonstrate the performance. It is found that the devices with an active area of 0.045 cm 2 show that with the increase of grain size, the average PCE increases from 14.00% to 17.42%, and the best device shows that its PCE is 17.80% with 4.04% hysteresis index. To show the possibility of scaling up, we fabricate a uniform perovskite thin film with an area of about 72 cm 2 , and a device with an active area of 1 cm 2 , which gives a PCE of 13.17% in reverse scan. In summary, our research provides a method of regulating the grain size for the vapor deposition, which can improve device performance by reducing the trap density in perovskite film for suppressing the carrier recombination in grain boundary. Meanwhile, we prepare high performance devices and large area thin films, showing their potential in large area device fabrication and applications.

High-efficiency solution-processed perovskite solar cells with millimeter-scale grains

Low trap-state density and long carrier diffusion in organolead trihalide perovskite single crystals

A Polymerization‐Assisted Grain Growth Strategy for Efficient and Stable Perovskite Solar Cells

Crystalline Liquid-like Behavior: Surface-Induced Secondary Grain Growth of Photovoltaic Perovskite Thin Film

Synergistic Improvement of Perovskite Film Quality for Efficient Solar Cells Via Multiple Chloride Salt Additives

Preparation of CsPbBr3 Films with Tens of Micrometer-Scale Grains and Preferential Orientation for Perovskite Solar Cells

Enabling Full-Scale Grain Boundary Mitigation in Polycrystalline Perovskite Solids.

Preparation of CsPbBr 3 Films with Tens of Micrometer-Scale Grains and Preferential Orientation for Perovskite Solar Cells

Non-wetting surface-driven high-aspect-ratio crystalline grain growth for efficient hybrid perovskite solar cells

Grain Boundary Elimination via Recrystallization‐Assisted Vapor Deposition for Efficient and Stable Perovskite Solar Cells And Modules

Unified Crystal Phase Control with MACl for Inducing Single‐Crystal‐Like Perovskite Thin Films in High‐Pressure Fusion Toward High Efficiency Perovskite Solar Cell Modules

Perovskite Monocrystals: Ultrathin Perovskite Monocrystals Boost the Solar Cell Performance (Adv. Energy Mater. 34/2020)

Coherent growth of high-Miller-index facets enhances perovskite solar cells

Polymer-templated nucleation and crystal growth of perovskite films for solar cells with efficiency greater than 21%

Pseudohalide-Assisted Growth of Oriented Large Grains for High-Performance and Stable 2D Perovskite Solar Cells

Anion Exchange‐Induced Crystal Engineering via Hot‐Pressing Sublimation Affording Highly Efficient and Stable Perovskite Solar Cells

Bulk Defect Suppression of Micrometer-Thick Perovskite Single Crystals Enables Stable Photovoltaics

Optimization of grain size to achieve high-performance perovskite solar cells in vapor deposition

In Situ Polymerization of Cross‐Linked Perovskite–Polymer Composites for Highly Stable and Efficient Perovskite Solar Cells

A pressure process for efficient and stable perovskite solar cells

Fast Growth of Thin MAPbI3 Crystal Wafers on Aqueous Solution Surface for Efficient Lateral‐Structure Perovskite Solar Cells