Abstract:This paper presents the machinability performance of uncoated, single-coated, and multicoated carbide tools during turning of Grade 5 (Ti6Al4V) Titanium alloy, which is challenging to machine due to its distinctive material properties. Coated tools with single-coated Titanium Aluminium Nitride (TiAlN) and multi-coated layer of Titanium Aluminium Nitride with Aluminium Chromium Nitride (TiAlN + AlCrN) coated inserts were utilized to assess surface roughness (Ra), tool wear rate (R), and chip morphologies under various cutting conditions using dry machining. Analysis of the used tools revealed that coated tools exhibited improved tool life and surface quality compared to uncoated tools across all cutting conditions. Multi-coated tools of TiAlN + AlCrN demonstrated a tool life increase of up to 15% compared to uncoated and single-coated tools, with surface roughness improvements ranging from 30 to 45% depending on cutting speed. Chip morphology analysis indicated an increase in the chip reduction coefficient with higher cutting speeds for all tool types. Coated tools exhibited the lowest chip-reduction coefficient due to the presence of TiAlN and AlCrN coatings, which control the tool chip contact length. Conversely, uncoated chip morphology resulted in larger chip thickness values compared to coated tools, particularly at cutting speeds above 100 m/min, attributed to poor heat dissipation and chemical reactions at the tool chip interface. Energy dispersive X-ray scanning electron microscopy (SEM/EDXS) analysis of worn uncoated inserts revealed a higher tendency towards Titanium adhesion compared to coated tools. The proposed multi-layer coatings of (TiAlN + AlCrN) used for dry machining proved highly beneficial for achieving economic machining objectives and may reduce the need for lubrication when processing Ti6Al4V alloys.

Study on Tool Wear and Cutting Force in Ti6Al4V Turning

Influence of Tool Geometrical Parameters on High Speed Cutting of Titanium Alloy Ti6Al4V

Study on Turning Force of Γ-Tial Alloy

Cutting Performance of TiN/TiSiN Coated Tool during Turning of Ti6Al4V Titanium Alloy

Study on the Orthogonal Cutting Process of Al7050T7451 with Uncoated and Coated Tools

A comparative study on tool life and wear of uncoated and coated cutting tools in turning of tungsten heavy alloys

Finite element analysis of Ti 1-x Al x N coated tools cutting performance and tool wear during Ti-6Al-4V milling

Inlfuences of Material Tool and Tool Wear on Cutting Temperature of Turning Titanium Matrix Composites

Investigation of tool wear and energy consumption in machining Ti6Al4V alloy with uncoated tools

Investigation of Cutting Force in High Feed Milling of Ti6al4v

Enhancing Tool Performance in High-Speed End Milling of Ti-6Al-4V Alloy: The Role of AlCrN PVD Coatings and Resistance to Chipping Wear

Analysis of tool wear of TiAlN coated tool, machined surface morphology and chip during titanium alloy milling

Multi-pattern failure modes and wear mechanisms of WC-Co tools in dry turning Ti–6Al–4V

Experimental Study on the Optimization of Ti1023 Milling Parameters

Surface integrity evolution and wear evolution of the micro-blasted coated tool in high-speed turning of Ti6Al4V

An Investigation of the Effect of Novel Mono/Bi-Layered PVD-Coated WC Tools on the Machinability of Ti-5Al-5V-5Mo-3Cr

A Simulation Study on the Effect of Micro-Textured Tools During Orthogonal Cutting of Titanium Alloy Ti-6Al-4V

Machinability Performance of Single Coated and Multicoated Carbide Tools During Turning Ti6Al4V Alloy

Effect of Al Content on the Wear Evolution of Ti1-xAlxN-Coated Tools Milling Ti-6Al-4V Alloy

Variation of Cutting Forces with Different Cutting Parameters and Tool Wear during Turning of 9442-Nickel-Aluminum Bronze

Study on tool wear in longitudinal-torsional composite ultrasonic vibration–assisted drilling of Ti-6Al-4V alloy