Abstract:Crystallites of a semicrystalline polylactide (cPLA) were induced in an amorphous PLA (aPLA) and its blends with poly(butylene adipate-co-terephthalate) (PBAT) to achieve in-situ self-reinforced PLA based structures. The approach involved the melt blending of cPLA as a minor phase with aPLA and its blends with PBAT at processing temperatures below the crystal melting peak of cPLA. An injection molding (IM) process was first adopted to obtain self-reinforced PLA (SR-PLA) structures at aPLA/cPLA weight ratios of 100/0, 95/5, 90/10, 85/15, and 80/20. IM barrel and mold temperatures revealed crucial impacts on preserving the cPLA crystallites and thereby enhancing the final mechanical performance of SR-PLA (i.e., aPLA/cPLA) samples. SR-PLA samples at various aPLA/cPLA weight ratios of 100/0, 90/10, 80/20, and 70/30 were then melt blended with PBAT to produce SR-PLA/PBAT at a given ratio of 85/15. These blends were first prepared in an internal melt mixer (MM) to evaluate the rheological properties. The rheological analysis confirmed the significance of cPLA reinforcing efficiency within SR-PLA and its corresponding blends with PBAT. Similar SR-PLA/PBAT blends were also prepared using the IM process to explore their thermal and mechanical characteristics. The effect of cPLA concentrations in blends was distinctive, leading to significant enhancements in stain at break and toughness values. This was due to the increased crystallite network within the matrix, further refining PBAT droplets. Morphological analysis of the melt-processed blends through MM and IM also revealed that the PBAT droplets were further refined when the IM process was applied. The induced shear during the molding could have further elongated the cPLA crystallites towards a fiberlike structure, which could additionally cause the matrix viscosity to increase and refine the PBAT droplets.

Preparation of ACR with Various Particle Sizes and Core-Shell Ratios and Its Toughening via PLA Blending

The Effect of Core–Shell Ratio of Acrylic Impact Modifier on Toughening PLA

PREPARATION AND CHARACTERISTICS OF PBA/PMMA CORE-SHELL PARTICLES AS TOUGHER

Preparation and Properties of PC/PLA Blend Toughened by ACR

Core-Shell Particles Of Poly(Methyl Methacrylate)-Block-Poly(N-Butyl Acrylate) Synthesized Via Reversible Addition-Fragmentation Chain-Transfer Emulsion Polymerization And The Polymer'S Application In Toughening Polycarbonate

Preparation of Acrylic Core/Shell Polymer and Its Application in Toughening Rigid PVC Matrix

Morphology and mechanical properties of Acrylonitrile-styrene-acrylate toughened plastics with block copolymer chain structure: Acrylonitrile-styrene-acrylate (ASA) toughened plastics with block copolymer chain structure

Toughening of polylactide with epoxy-functionalized methyl methacrylate–butyl acrylate copolymer

Grafting Modification of the Reactive Core-Shell Particles to Enhance the Toughening Ability of Polylactide

In Situ Formation of the Core–Shell Particles and Their Function in Toughening PA6/SEBS-g-MA/PP Blends

Synthesis of ACR Impact Modifier with PVC Shell and Its Toughening Efficiency on PVC

Toughening of Poly(L-Lactide) Modified by A Small Amount of Acrylonitrile-Butadiene-Styrene Core-Shell Copolymer

Modification of Reactive PB‐g‐SAG Core–shell Particles to Achieve Higher Toughening Ability for Brittle Polylactide

Effect of Core-shell Ratio of the Modifier on the Properties of Toughened Polylactide Acid

In Situ Anionic Polymerization and Mechanical, Thermal and Morphological Properties of Toughened and Volume-Enhanced Blends of Poly(lactic Acid)

Thermal and Mechanical Properties of Polylactide Toughened with A Butyl Acrylate-Ethyl Acrylate-Glycidyl Methacrylate Copolymer

In-situ self-reinforcement of amorphous polylactide (PLA) through induced crystallites network and its highly ductile and toughened PLA/poly(butylene adipate-co-terephthalate) (PBAT) blends

Structure and Property of Epoxy-Functionalized Acrylic Rubber Toughened Polylactide

Toughening PLA with E-MA-GMA

Polylactide Toughening with Epoxy‐functionalized Grafted Acrylonitrile–butadiene–styrene Particles

Effect of Reactive Group Types on the Properties of Core-Shell Modifiers Toughened PA6