Abstract:In this work, surface analysis technology is employed to investigate the removal mechanism and the selection of abrasive during fused silica chemical mechanical polishing (CMP). Morphology of abrasives is inspected by scanning electron microscope (SEM). The atomic force microscope (AFM) is used to determine the surface roughness (Rq) and undulating (PV) of the polished fused silica surface. The results show that abrasive morphology has a tremendous influence on removal rate (MRR) and PV but has little effect on the Rq. The AFM and infrared spectroscopy (IR) analysis show that a soft layer, called “silica gel membrane (SGM),” existed on the polished surface is the critical reason for the differences of MRR, Rq, and PV during CMP. For three kinds of micro-ceria abrasives, the abrasive with a rougher surface gets more opportunities to contact the surface of fused silica, yielding higher MRR. Regarding different kinds of nano-abrasives, there are more SGM induced by nano-ceria abrasive resulting from higher chemical reaction rate. The element contaminations on the polished fused silica have been assessed using X-ray photoelectron spectroscopy (XPS), and the results suggest that there are depths of 3.6 and 5.4-nm element contaminations on the polished surface of fused silica with nano-ceria and nano-alumina abrasives, respectively. While the surface polished by nano-silica is free of heterogeneous element contaminations. Based on study results, a novel polishing slurry is designed by modifying the chemical composition of nano-silica. Comparing with ceria-based slurry, the silica-based slurry has better removal efficiency, and surface quality in fused silica precision machining. © 2019 John Wiley & Sons, Ltd.

Research on Wet Ultra-fine Grinding of Semctite

Wet Grinding of Montmorillonite and Its Effect on the Properties of Mesoporous Montmorillonite

An Experimental Investigation on Ultrasonic Vibration-Assisted Grinding of Sio2f/Sio2 Composites

Studies on the Surface Quality of the Unsteady-State Grinding Technique

Effect of Ultrasonic Vibration Assisted Grinding Process on Surface Topography and Properties of C/SiC Composite

A Novel Method for Purification of Low Grade Diatomite Powders in Centrifugal Fields

Research on the Mechano-chemical Effect of Natural Zeolite During Wet Ultrafine Grinding by Stirred Mill

The role of sodium tripolyphosphate in wet grinding process of magnesite

Research on Preparation and Properties of Magnetic Abrasive by Conventional Solid-State Method

Application of surface analysis in study on removal mechanism and abrasive selection during fused silica chemical mechanical polishing

Methods and Mechanistic Analysis of Improving the Dispersion of Nano Silica Colloidal Particles in Chemical Mechanical Polishing Slurries

Wet Grindability of Calcite to Ultra-Fine Sizes in Conventional Ball Mill

Ultra-Fine Treatment of Sic Powder and Its Effect on Microstructure and Properties of Sic Ceramic

Dry-grinded ultrafine cements hydration. physicochemical and microstructural characterization

Ultrafine dry grinding of talc by planetary mill: effects of operating conditions

Optimizing of the Colloidal Dispersity of Silica Nanoparticle Slurries for Chemical Mechanical Polishing

Effects of C-S-H Seed Prepared by Wet Grinding on the Properties of Cement Containing Large Amounts of Silica Fume

Dry Grinding Effect on Pyrophyllite-Quartz Natural Mixture and Its Influence on the Structural Alternation of Pyrophyllite.

Effect and Mechanism of Superplasticizers on Microstructure and Properties of Ultrafine Sulfoaluminate Cement-Based Grouting Materials

Preparation of Silane Modified Sio2 Abrasive Particles and Their Chemical Mechanical Polishing (cmp) Performances

Cavitation Effect in Ultrasonic-Assisted Electrolytic In-Process Dressing Grinding of Nanocomposite Ceramics