DISSCUSSION ABOUT VOLTAGE-SENSITIVE WHEATSTONE ELECTRICAL BRIDGE

Wang Jinhui,Xia Zhanggen,Zhao Tiesong

DOI: https://doi.org/10.3969/j.issn.1009-7104.2006.03.010

2006-01-01

Abstract:The sensitivity, significant figures and errors of voltage-sensitive Wheatstone bridge are primarily discussed.

What problem does this paper attempt to address?

Effect of Sensitivity of Wheatstone Electrical Bridge Using Constant-Current Source

Jin-hui WANG,Li-rong HE,Jia-bin LIU,Hong ZHOU,Xue-hao SHEN

DOI: https://doi.org/10.14139/j.cnki.cn22-1228.2015.006.020

2015-01-01

Abstract:The sensitivity of Wheatstone bridge circuit using constant-current source has been discussed. The experimental and theoretical results show that the sensitivity is proportional to the output current of the source, and exhibits greater value with decreasing the resistance ratio of the bridge-arm resistors and increasing the val-ue of the bridge-arm resistors.
A Dynamic Voltage Compensation Method for Improving Weighing Accuracy

Yin Rongsen,Yang Jiaqiang

DOI: https://doi.org/10.4028/www.scientific.net/amm.333-335.317

2013-01-01

Applied Mechanics and Materials

Abstract:In order to eliminate the measurement error caused by working voltage fluctuation of weighing sensor, a dynamic voltage compensation method for improving the weighing accuracy was proposed in the paper. The method takes strain gauge type pressure sensor as the weighing sensor and corrects Wheatstone bridge circuit. By synchronously detecting output voltage signal and working voltage of the weighing sensor, the method dynamically compensates the working voltage fluctuation of the weighing sensor, corrects the measurement error caused by the voltage fluctuation of external source and calculates the weight in real time. A weighing system based on the digital signal processor (DSP) was designed. Results of simulation experiment verify the feasibility of the proposed method.
Design and Optimization of Wheatstone Bridge Adjustment Circuit for Resistive Sensors

Yuanfei Zhang,F. Ni,Hong Liu

DOI: https://doi.org/10.1109/JSEN.2023.3274927

IF: 4.3

2023-07-01

IEEE Sensors Journal

Abstract:A novel Wheatstone bridge adjustment circuit with both rough-tuning and fine-tuning functions is designed for balancing the Wheatstone bridge in this article. Firstly, the parametric circuit structure is constructed to facilitate the design of rough-tuning and fine-tuning sub-circuit parameters; Secondly, the quantitative index of Wheatstone bridge imbalance is defined, and the parameter design flow of the rough-tuning sub-circuit, which consists of two sets of series-parallel-resistor (SPR) structures that are, respectively, connected in parallel with the two branches of one half-bridge, is given to directly weaken the initial bridge imbalance in the manufacturing stage. Theoretical analysis results show that the SPR structure can effectively approach any expected value and reduce the number of fixed resistor types. Thirdly, parameters of the fine-tuning sub-circuit, which consists of a resistor and a digital-to-analog converter (DAC), are optimized based on any expected adjustable range. Adjusting the DAC input to seek the middle value of an analog-to-digital converter (ADC) output, indirectly eliminates the additional bridge imbalance caused by mechanical assembly stress, gravity, ambient temperature, etc., in the application stage. Then the influence of the fine-tuning parameters on linear fitting coefficients of the output versus input of the Wheatstone bridge is analyzed theoretically. The results show that the DAC output voltage only has a significant linear impact on the intercept coefficient, while its impact on the scale coefficient is negligible. Finally, the effectiveness of the adjustment circuit is verified on a six-axis force/torque sensor that is developed for an Experimental Module Manipulator (EMM) in the Chinese Space Station (CSS).

Engineering
An Experimental Approach for Characterisation of Concrete Damage Using the Wheatstone Bridge Circuit

Teuku Ferdiansyah,Jean-Paul Balayssac,Anaclet Turatsinze

DOI: https://doi.org/10.1007/s40999-021-00659-z

IF: 2.184

2021-08-04

International Journal of Civil Engineering

Abstract:In this paper, a method for the detection of concrete damage under three bending test using Wheatstone bridge concept is presented. The damage is detected by monitoring a change in voltage drop (ΔV) at the Wheatstone bridge. Good correlations between crack opening and voltage drop and between damage variable and voltage drop were observed. Results of these tests confirmed that the voltage drop increase with the increase of the damage. The voltage drop significantly increases from 0.005 to 0.340 V when the damage variable increases from 0.005 to 0.93. At this stage, specimen can be considered as completely fractured. Thus, this underlines that the self-sensing method using Wheatstone bridge as the concept of electrical resistance concrete measurement is one potential technique to detect mechanical damage. Furthermore, a special effort was put on investigation of the optimal location of electrodes, i.e. which location along the specimens is the most sensitive to the damage, and the higher sensitivity is obtained when the electrodes are close to the crack location. It has been found that the sensitivity may drop by 50% when the distance between the sensor and the notch tip increases of 400%. Finally, digital image correlation (DIC) technique is also used to investigate the crack propagation during the test and to define its correlation with Wheatstone bridge voltage drop.

engineering, civil
DESIGN AND REALIZATION AND TESTING OF WIRELESS MEASUREMENT SYSTEM FOR BRIDGE BASED ON THE RESONANT WIRE TRANSDUCER

Huang Qiao,Li Zhonglong,Sha Xuejun,Xu Yubin,Zhang Lianzhen

2008-01-01

Abstract:In order to resolve the problems in traditional strain collection and transmission system, a wireless system using resonant wire transducer s is proposed which can be applied to bridge structural strain monitoring. Firstly, working principles and design rules of pivotal modules are discussed. Secondly, design of system software is discussed. Finally, the wireless measurement system is experimentized at Xichang Cable-stayed bridge. The research shows that: the wireless system has not only well precision, but also many other good characteristics as transmitting reliably, operation simpleness, high-reliable, without using the present communication network and low cost. It is applicable to bridge engineering monitoring.
Tunable nanowire Wheatstone bridge for improved sensitivity in molecular recognition

Carsten Maedler,Shyamsunder Erramilli,L. J. House,M. K. Hong,Pritiraj Mohanty

DOI: https://doi.org/10.1063/1.4789994

IF: 4

2013-01-28

Applied Physics Letters

Abstract:Poor signal-to-noise ratio (SNR) is a strong limiting factor on the performance of nanowire field-effect transistor based sensing of molecules. Using an advanced measurement configuration such as a Wheatstone bridge, electrical noise, drift due to fluid dynamics, thermal fluctuations, and chemical changes of the gate oxide can be drastically reduced. Here, a miniature Wheatstone bridge has been lithographically fabricated. All four arms consist of silicon nanowires, while two of the arms are tunable by top gate electrodes to enable balancing of the bridge. We have studied the performance of the bridge for pH detection. The signal-to-noise ratio is significantly enhanced in the balanced configuration, which also helps to reduce overall drift.

physics, applied
Enhancing Undergraduate Physics Education: A Pedagogical Exploration of the Wheatstone Bridge with Symmetry and Simulation

Yong Zhou,Ze-yan Peng,Yan Xiao,Wen-mei Guo,Guan-xin Yao

2024-11-22

Abstract:The Wheatstone bridge experiment is a fundamental component of the undergraduate physics curriculum, traditionally taught as a hands-on activity to explore resistance measurement and circuit balancing. This study introduces a pedagogical approach that combines qualitative symmetry-based analysis with quantitative computer-based sensitivity simulations, enhancing students' understanding and engagement. A key focus is demonstrating how balanced configurations in the Wheatstone bridge affect circuit sensitivity, providing students with an intuitive grasp of the relationship between symmetry and measurement accuracy. Using simulations, we investigate the impact of internal resistances in the galvanometer and power supply, showing that lower resistances increase the circuit's sensitivity to minor resistance changes. Additionally, various resistor configurations are analyzed, highlighting the effect of careful adjustments in achieving maximal sensitivity. A Bayesian optimization-based software tool was developed to guide students in selecting optimal component values, thereby minimizing the need for manual adjustments while ensuring accurate measurements. This integrated approach bridges traditional experimentation with computational techniques, fostering critical thinking and preparing students for modern scientific practices. The study demonstrates that this enriched methodology significantly enhances the learning experience, equipping students with valuable skills in both experimental and computational aspects of physics.

Physics Education
Design and Validation of Wireless Strain Test System for Bridge Based on the Resistance Strain Sensor

Qiao Huang,Zhonglong Li,Lianzhen Zhang,Sha Xue-jun,Yan Xu,Dejun Wang

2010-01-01

Abstract:In order to achieve an access to strain sensor data with wireless transmission in bridge engineering structure testing, a wireless strain test system is presented based on the resistance strain sensor of networks. The wireless bridge strain test system composed of master station and substation adopts the wireless method to realize the high accuracy data acquisition between the master station and the substation under a reliable communication protocol. The system has been tested in contrast with the present strain apparatus. Results show that the wireless system is high-reliable, and has many characteristics such as high efficiency, good precision, high stability with low cost, and good flexibility, without using the present communication network.
Linear Spin-Valve Bridge Sensor For Weak Magnetic Fields

Wei Li,Huarui Liu,Tianling Ren,Litian Liu,Xun Zhang

DOI: https://doi.org/10.1109/NEMS.2006.334834

2006-01-01

Abstract:Spin-valves are utilized in a variety of devices including magnetic sensors and biological detection systems. The sensing devices are characterized by three parameters: the sensing field range, sensitivity and linearity. The linear spin-valve sensing element is configured as a Wheatstone bridge. Two kinds Wheatstone bridge were investigated. First, the bridge consist of two sensing resistors and two fixed value resistors, which has no hysteresis and linearity error is less than 0.15% in the operation range of -6 Oe to 6 Oe, shows a sensitivity of 0.78 mVN.Oe. Second, the linear bridge sensor consisting of four sensing resistors shows a sensitivity of 1.54 mV/V.Oe in the operation range of -6 Oe to 6 Oe and a linearity error less than 0.3%.
Research and Development of a Wireless Self-Powered Sensing Device Based on Bridge Vibration Energy Collection

Xinlong Tong,Yun Hou,Yuanshuai Dong,Yanhong Zhang,Hailu Yang,Zhenyu Qian

DOI: https://doi.org/10.3390/s21248319

2021-12-13

Abstract:Traditional bridge monitoring has found it difficult to meet the current diversified needs, and frequent replacement of sensor batteries is neither economical nor environmentally friendly. This paper presents a wireless acceleration sensor with low power consumption and high sensitivity through integrated circuit design, data acquisition and wireless communication design, package design, etc. The accuracy of the sensor in data collection was verified through calibration and performance comparison tests. The ability of triangular piezoelectric cantilever beam (PCB) was tested through design and physical manufacture. Finally, the self-powered performance of the sensor was tested by connecting the sensor and the triangular PCB through a circuit, which verifies the feasibility of using the PCB to collect bridge vibration energy and convert it into electrical energy to supply power for sensor, and also explore the green energy collection and application.
Design and Experimental Investigations of a Vibration Based Wireless Measurement System for Bridge Cable Tension Monitoring

yan yu,chunwei zhang,xinqun zhu,w kang,xingquan mao,brian uy

DOI: https://doi.org/10.1260/1369-4332.17.11.1657

2014-01-01

Advances in Structural Engineering

Abstract:Cables are important components of a cable-stayed bridge, and the cable tension is a crucial factor in determining the overall condition assessment of a cable-stayed bridge structure. Based on the vibration frequency method, a wireless monitoring system for bridge cable tension force monitoring has been investigated and experimentally validated through laboratory and field tests in this paper. The vibration frequency-based method for cable tension measurement, the design method of the wireless measurement system with embedded identification algorithm, the test procedures, and relevant results are discussed, respectively. The developed wireless monitoring system is verified by a bridge model test in the laboratory and full-scale bridge tests in the field. Field experimental results show that the relative error between this wireless monitoring system and the reference wired system values is within 0.5%. Therefore, the developed wireless measurement system can provide an estimation of cable tension with sufficient accuracy. Moreover, the developed system is highly integrated and convenient in terms of installation and dismantling, and it has potential applicability prospects in emergency for the quick detection of cable tension.
Design and Validation of Wireless Dynamic Testing System for Bridge Based on the 941B Type Vibration Sensor

Zhonglong Li,Lianzhen Zhang,Xiaodi Zhu,Hongjiang Gu,Zitian Jiang

DOI: https://doi.org/10.1061/41064(358)30

2009-01-01

Abstract:In order to ensure the safety of the bridge operation, Structural Health Monitoring (SHM) or regular tests should be carried out. SHM or regular tests are very important for large structures such as suspension bridges, cable-stayed bridges, cross-ocean bridges, towers, and so on. Much more attention have been paid to some advanced technologies for SHM or regular tests. In order to collect signals wirelessly in civil engineering structure monitoring, a Wireless Dynamic Testing System was designed by modularization and system method, which combines bridge structure detection technique, computer technology, modern sensor technology, wireless communication, and system technology. The wireless testing system consists of a master station and several substations. The master station is composed of a control center subsystem and a data transmission subsystem. The substation is composed of a data transmission subsystem and a gathering subsystem. The software system consists of controlling, data, and Single Chip Microcomputer processing. Finally, the wireless measurement system is tested by a field test of the Sifangtai Cable-stayed Bridge.
High Sensitivity Pressure Sensor Using Tandem Wheatstone Bridge for Low Pressures

Yuanying Zhang,Wei Cui,Jinjun Deng,Xiubing Liang,Xiaoliang Luo,Xiaojing Wang,Binghe Ma,Jian Luo

DOI: https://doi.org/10.1109/jsen.2024.3356121

IF: 4.3

2024-01-01

IEEE Sensors Journal

Abstract:A tandem Wheatstone bridge low-pressure (TWBLP) sensor with high sensitivity which can be widely used in medical and industrial fields has been designed and fabricated. Compared with the conventional low-pressure (CLP) sensor, the TWBLP sensor membrane is arranged with eight piezoresistors, which are formed into two Wheatstone bridges. They achieved the detection of membrane stress with different positions and different directions. The output ports of the two Wheatstone bridges are connected in tandem to realize the non-interference superposition of the output electric potential, thus improving the sensitivity of the sensor. The structure of the sensor membrane and the position of the piezoresistors are optimized using the finite element analysis (FEA). The TWBLP sensor is simple in structure design and easy to produce in large quantities, with the advantage of high sensitivity, which can provide tiny pressure measurement results for pressure measurement in related fields. In the laboratory environment, the local atmospheric pressure is used as the reference zero point to calibrate the sensor. The test results show that the sensitivity of the TWBLP sensor is 26.20% higher than that of the CLP sensor. For the measurement range from −10 to 10 kPa, the fabricated sensor achieves a high sensitivity of 23.07 mV/kPa and an accuracy of 0.19%F.S.

engineering, electrical & electronic,instruments & instrumentation,physics, applied
SEISMIC VULNERABILITY ANALYSIS AND A SHAKING TABLE TEST OF A NEAR-FAULT CONTINUOUS VIADUCT

li yong,yan weiming,liu jingbo,jie mengfei

DOI: https://doi.org/10.6052/j.issn.1000-4750.2017.03.0236

2018-01-01

Abstract:Compared with far-field earthquake records, near-fault earthquake records contain long-period components and large velocity pulses which can lead to more severe seismic damage of flexible bridges. Continuous viaducts are a common type of bridge and suffer more if they are close to seismic faults. Seismic vulnerability analysis was conducted on a typical four-span continuous viaduct subjected to near-fault and far-field earthquake record inputs. Subsequently, a shaking table test was conducted to obtain dynamic responses of the viaduct under typical near-fault earthquake excitations. The analysis results showed that the vulnerability under near-fault earthquake excitations with velocity pulses was higher than that under far-field or design seismic record inputs. For seismic vulnerable analysis of bridge systems the damage measures of piers and bearings should be taken into consideration synthetically. The shaking table test also showed that the tested dynamic response subject to typical near-fault earthquake records was higher than that subject to far-field or artificial earthquake records.
Experimental Investigation and Understanding of the Intermittent Molten Bridge Phenomena and Mechanism of Contacts With Superlow Opening Speed

W. Ren,H. Wang,C. Chang,S. Xue

DOI: https://doi.org/10.1109/TCPMT.2016.2530118

2016-01-01

Abstract:The molten bridge phenomena of gold-plated material at superlow opening speed conditions are studied by introducing our newly designed test rig. The typical waveforms in the contact voltage and contact force during opening are investigated under the load of 5/25 V at 0.2/0.5/1 A and the speed of 25~150 nm/s. It is demonstrated that the intermittent molten bridge phenomena are resulted from the competition of multitude contact a-spots for current distribution. Furthermore, the measured tension force during breaking closely correlates with the occurred molten bridge. Based on the capillary force model, surface analytical technique, thermal equilibrium principle, and the change in the bridge length and duration, the physical mechanism of the intermittent molten bridge under different load conditions is proposed.
A Two-Level Voltage Stability Monitoring Method Based On P-V Sensitivity Assessment

Junlei Liu,Huaichang Ge,Yinguo Yang,Qinglai Guo,Feng Qian,Hongbin Sun,Mingye Zhang,Bin Wang

DOI: https://doi.org/10.1109/pesgm.2017.8274188

2017-01-01

Abstract:In this paper, the authors will introduce a two-level voltage stability evaluation method consists of control center level and substation level. At control center level, some certain sensitivities related with operation state of overall system are calculated and these variables are sent to several substations. At substation level, the proposed method adopts a different system model rather than The venin Equivalent Circuit, such that the results of local voltage stability assessment are more accurate than traditional distributed methods. The performance of the proposed method is tested on IEEE 39-bus system.
A Study on PVDF Sensor Using Wireless Experimental System for Bridge Structural Local Monitoring

Yan Yu,Xuefeng Zhao,Yang Wang,Jinping Ou

DOI: https://doi.org/10.1007/s11235-011-9558-5

2010-01-01

Abstract:Originated from aerospace area, smart material structures have been a research hotspot in the application of engineering. For structural health monitoring within the context of civil engineering, the research about high-performance sensing units are very important. As one of the piezoelectric materials belonging to smart ones, Polyvinylidene Fluoride (PVDF) is widely regarded for its property advantages of low cost, good mechanical abilities, high sensibility, and corrosion resistance. In this paper, for the validation of PVDF sensors as sensing units for bridge structural local monitoring, wireless experimental systems of PVDF sensor for structural local monitoring on a bridge model and beam were built. Firstly, based on the operating mechanism, the measurement circuit and the characteristics of PVDF are introduced. Secondly, system framework of PVDF sensor for local monitoring is proposed, a bridge model is built, wireless sensor kits are then developed. Finally, Bridge damage monitoring experiments have been done for structural local health monitoring using PVDF sensors. The experimental results show that PVDF sensor can handle structural impact response monitoring and damage detection of civil engineering, and the developed wireless sensor experimental system can be easily implemented for use in practical monitoring engineering.
Study on feasibility of ramp current sensitivity testing method

YW Bai,ZD Jiang,YL Zhao,EY Chu

2005-01-01

Abstract:A new designed ramp current apparatus is used to test sensitivity of bridge-wire electrical Initiating Device. The results show that the apparatus was feasibility for sensitivity test. By using different charged device and comparing the testing results with up-and-down method's results, it verifies the method can be used to detect disfigurement and difference of the Electrical Initiating device. It can be used to evaluate the system's fire character during designing phase. Because each sample testing result can be used, fewer samples are utilized in this testing method.
Study on the Contact Resistance and Temperature-rise Performance of High-voltage Vacuum Interrupter

Zhaode Wu,Haibo Su,Junxiang Liu,Yongpeng Mo,Shuwei Fan,Shenli Jia

DOI: https://doi.org/10.23919/ISDEIV55268.2023.10200582

2023-01-01

Abstract:The temperature rise under continuous current is one of limitations on the development of vacuum interrupters (VIs). The contact resistance is one of the main heat sources. As a traditional contact resistance model, the conductive bridge is widely used in thermal simulation of medium-voltage and low-voltage contacts. Only the shrinkage resistance exists in the high-voltage vacuum contact, and the diameter of the contact is quite large, which means the influence of the current path on the contact plates is much more significant. In order to study thermal characteristics of high-voltage VI, a three-dimensional model was established and the conductive bridge was then verified by simulation and experiment. The results indicated that the traditional single conductive bridge could not accurately represent the contact resistance of high-voltage vacuum cup-type contacts. On the basis of the traditional conductive bridge, the number and position of the bridge were changed, and the simulation results were more consistent with the experimental values. Based on the multiple conductive bridges, the steady-state temperature-rise performance of high-voltage VI was analyzed through electromagnetic-thermal-flow coupling simulations. The results showed that the temperature rise of the contact plate was the highest, which was 296.83K, and the temperature gradually decreased from the contact plate to the conductive rod.
Simple phase-sensitive detector for Wheatstone bridge resistance measurements

D. DiBartolomeo,J. Klems

DOI: https://doi.org/10.1063/1.1138164

1985-05-01

Abstract:A simple and economical phase‐sensitive detector circuit is described. The circuit, which was developed for use with large‐area heat‐flow sensors that employ resistance temperature detection, uses a synchronous rectifier driven by a square wave. It is shown that the circuit has good linearity, resolution, and immunity to external and internal noise.

Engineering,Materials Science,Physics

DISSCUSSION ABOUT VOLTAGE-SENSITIVE WHEATSTONE ELECTRICAL BRIDGE

Effect of Sensitivity of Wheatstone Electrical Bridge Using Constant-Current Source

A Dynamic Voltage Compensation Method for Improving Weighing Accuracy

Design and Optimization of Wheatstone Bridge Adjustment Circuit for Resistive Sensors

An Experimental Approach for Characterisation of Concrete Damage Using the Wheatstone Bridge Circuit

DESIGN AND REALIZATION AND TESTING OF WIRELESS MEASUREMENT SYSTEM FOR BRIDGE BASED ON THE RESONANT WIRE TRANSDUCER

Tunable nanowire Wheatstone bridge for improved sensitivity in molecular recognition

Enhancing Undergraduate Physics Education: A Pedagogical Exploration of the Wheatstone Bridge with Symmetry and Simulation

Design and Validation of Wireless Strain Test System for Bridge Based on the Resistance Strain Sensor

Linear Spin-Valve Bridge Sensor For Weak Magnetic Fields

Research and Development of a Wireless Self-Powered Sensing Device Based on Bridge Vibration Energy Collection

Design and Experimental Investigations of a Vibration Based Wireless Measurement System for Bridge Cable Tension Monitoring

Design and Validation of Wireless Dynamic Testing System for Bridge Based on the 941B Type Vibration Sensor

High Sensitivity Pressure Sensor Using Tandem Wheatstone Bridge for Low Pressures

SEISMIC VULNERABILITY ANALYSIS AND A SHAKING TABLE TEST OF A NEAR-FAULT CONTINUOUS VIADUCT

Experimental Investigation and Understanding of the Intermittent Molten Bridge Phenomena and Mechanism of Contacts With Superlow Opening Speed

A Two-Level Voltage Stability Monitoring Method Based On P-V Sensitivity Assessment

A Study on PVDF Sensor Using Wireless Experimental System for Bridge Structural Local Monitoring

Study on feasibility of ramp current sensitivity testing method

Study on the Contact Resistance and Temperature-rise Performance of High-voltage Vacuum Interrupter

Simple phase-sensitive detector for Wheatstone bridge resistance measurements