Abstract:1.4 %C ultra high carbon steel (UHCS) was prepared in order to study the structure of martensite transformation and mechanical properties. Ultra-fine spherical carbide and ultra-fine austenite grain size were obtained. A great deal of lath martensite was observed after quenching. The phenomenon does not agree with the traditional knowledge that the lath martensite would disappear when carbon content is in excess of 0.8% in austenite. The strength, fatigue properties and fracture toughness have been measured. A good combination of strength, toughness and fatigue properties come from fine and uniform distributed carbide particles and ultra-fine austenite grain size. Fracture strength increases by 48%, yield strength increases by 15% and plasticity keep the same comparing with that of hardened and tempered 40CrNiMo. The carbon content of ultrahigh carbon steels (UHCS) is in the range of 1.0-2.1% [1, 2]. Traditional heat treatments for normal steels will cause the microstructure of UHCS to be coarse and do not produce optimal properties. With controlled rolling and special heat treatment, UHCS can be in ferrite, pearlite, bainnite or martensite structures, which all have different mechanical properties. The yield stress of a 1.8%C, 1.6%Al ferrite UHCS can reach 1500MPa, which is much higher than that of high strength and plain alloy steels [3]. The tensile strength of a 1.25%C-1.5%Cr pearlite UHCS can reach 1810Mpa and its elongation can be 18%. When it is treated into martensite, its compression strength reached to 4690Mpa and compression strain reached to 26% [1, 4], which is comparable to WC-12Co. Such good mechanical properties can be ascribed to the ultra fine grain sizes because of the undissolved carbide particles which resist growth of austenite grain during heating. Another reason could be the lath martensite structures. O.D.Sherby [4] had reported that there was a lot of lath martensite in quenched UHCS. The UHCS was considered not only as tool steels but also as good structure materials. Fracture and fatigue properties are important for structure materials. However, they have rarely been studied. The present paper is going to study the martensite structure and mechanical properties of a prepared 1.4% C UHCS.

Superplasticity in Ultrahigh Carbon (1.6 Pct C) Steel

Study on High-temperature Superplasticity of 1.6%C Ultra-high Carbon Steel

Processing and Properties of Ultrahigh-Carbon (1.6%C) Steel

Microstructure and mechanical properties of a 1.6C (pct) ultra-fine grained ultra-high carbon steel

Dynamic reverse phase transformation induced high-strain-rate superplasticity in low carbon low alloy steels with commercial potential

Superplastic characteristic of Mn–Si–Cr alloyed ultrahigh carbon steel realized through a novel process

Revealing the Superplastic Deformation Behaviors of Hot Rolled 0.10c5mn2al Steel with an Initial Martensitic Microstructure

Deformation mechanisms for superplastic behaviors in a dual-phase high specific strength steel with ultrafine grains

An Ultrahigh Strength Steel with Ultrafine-Grained Microstructure Produced Through Superplastic Forming

Excellent Low Temperature Superplasticity and Its Deformation Mechanism in Nano/ultrafine Grained Fe-17Cr-6Ni Stainless Steel

Microstructure and properties of ultrafine grained ultrahigh carbon (1.73 Pct C) steel

Ultrahigh strength-high ductility 1 GPa low density austenitic steel with ordered precipitation strengthening phase and dynamic slip band refinement

Superplasticity-like behavior of ultrafine-grained austenitic steel 321

Microstructure and Mechanical Properties of A 1.4%C Ultra High Carbon Steel

Microstructure Evolution and Constitutive Modeling of Cu-Bearing High-Strength Low-Alloy Steel During Hot Deformation

Study on Spheroidizing Structure and Properties of Ultrahigh Carbon Steel

Microstructure and Properties of 1.6%C Ultra-high Carbon Steel

Microstructure and Mechanical Properties of A Ultra-High Carbon Steel

Extraordinary superplasticity at low homologous temperature and high strain rate enabled by a multiphase nanocrystalline network

Stress-strain behavior and microstructural evolution of ultra-high carbon Fe-C-Cr-V-Mo steel subjected to hot deformation

Microstructure, mechanical properties and deformation behavior of Cr-containing triplex low-density steels with different C content