Abstract:Similar preforms are manufactured for both the permeability tests and vacuum infusion. The microstructure of the vacuum infused sample is analysed in the filament length scale under different levels of compaction. Comparison of the experimental and numerical results, where the latter are derived from the filament distribution statistics, shows a good ageement and provides a valuable insight on the relationship between the apparent transverse permeability and microstructural transformation through compaction. The transverse permeability of roving/tow‐based fiber reinforcement is of great importance for accurate flow modeling in the pultrusion process. This study proposes an experimental approach to characterize the roving‐based fiber beds' permeability under different compaction conditions. The experimental permeability results of thick roving‐based preforms were reported and compared with the permeability values of roving‐based preforms in the literature. A representative preform was infused under vacuum conditions. Its thickness was varied to replicate the different compaction values observed in permeability tests. Micrographs were then collected from it and analyzed to highlight the microscale transformations caused by processing/compaction on the fiber arrangement. The analysis revealed that compaction resulted in the reorganization of filaments along the direction of the applied compaction. Overall, the uniformity of the spatial filament distribution, i.e., the homogeneity within the fibrous domain, increased with increasing compaction. Furthermore, the microstructural analysis demonstrated transverse anisotropy within the tested domains, indicating that the obtained permeability results represented an upper boundary. In addition to the experimental analyses, various transverse permeability models, which were developed based on recently introduced statistical descriptors of fiber distribution, were evaluated by using the statistical descriptors extracted from the analyzed cross‐sections. Among these models, the one correlating the second neighbor fiber distance with apparent permeability exhibited good agreement with the experimental results. Highlights Transverse permeability measurement of a roving‐based reinforcement was presented. The influence of compaction on the microstructure was investigated at the filament level. Filament distribution in a pultruded profile was analyzed by using statistical descriptors. The results of the experiments and the models in the literature were compared. The correlation between microstructural features and apparent permeability was discussed.

Permeability Characterization. Part 2: Flow Behavior in Multiple‐layer Preforms

Permeability of Hybrid Reinforcements and Mechanical Properties of their Composites Molded by Resin Transfer Molding

EFFECT OF LAYERS ON PERMEABILITY

Unsaturated Flow Behavior in Double-Scale Porous Reinforcement for Liquid Composite Molding Processes

Evaluation of through-thickness permeability and the capillary effect in vacuum assisted liquid molding process

On the design of test molds based on unidirectional saturated flows to measure transverse permeability in liquid composite molding

Saturated transverse permeability of unidirectional rovings for pultrusion: The effect of microstructural evolution through compaction

Numerical evaluation of the transverse permeability determination experiment

Numerical prediction strategy of fabric in‐plane permeability considering realistic inter‐ and intra‐tow geometry

Flow Front Monitoring in High-Pressure Resin Transfer Molding Using Phased Array Ultrasonic Testing to Optimize Mold Filling Simulations

Sensor Fusion for Simultaneous Estimation of In-Plane Permeability and Porosity of Fiber Reinforcement in Resin Transfer Molding

Study on Void Formation in Multi-Layer Woven Fabrics

Resin Impregnation During the Manufacturing of Composite Materials Subject to Prescribed Injection Rate

A 2D modeling approach for fluid propagation during FE-forming simulation of continuously reinforced composites in wet compression moulding

Resin percolation and intimate contact in fast processing of thermoplastic composites

Darcy Permeability of Hollow Fiber Membrane Bundles Made from Membrana Polymethylpentene Fibers Used in Respiratory Assist Devices

Morphology and Transport Properties of Fibrous Porous Media

A neural-network-assisted method for flow-front estimation in resin transfer molding using pressure sensors

Investigation of Transport Property of Fibrous Media: 3D Virtual Modeling and Permeability Calculation

Numerical Analysis on Microscopic Flow Behavior of Resin with Resin Transfer Molding(rtm)process

An approach to couple mold design and on-line control to manufacture complex composite parts by resin transfer molding