Abstract:The rod-fastened rotor is comprised of a series of discs damped together by a central tie rod or several tie rods on the pitch circle diameter. The equivalent flexural stiffness of contact interfaces in the rod-fastened rotor is the key concern for accurate rotor dynamic performance analysis. Each contact interface was modeled as a bending spring with stiffness of K-e and a hinge in this study. The contact states of the contact interfaces which depend on the pre-tightening forces and bending moments (static) have effects on K-c. The approach to calculating K-e in two contact states is presented. The first contact state is that the whole zone of the contact interface is in contact, K-e is determined by the contact layer which consists of asperities of the contact surfaces. Hertz contact theory and the GW (Greenwood and Williamson) statistical model are used to calculate the equivalent flexural stiffness of the contact layer Kce. The second contact state is that some zones of the contact interface are separated (when the bending moment is relative large), the equivalent flexural stiffness of the rotor segment Ksf (not include Kc) decreases as the material in the separated zone has no contribution to the bending load carrying capacity of the rotor The strain energy which is calculated by the finite element method (FEM) is used to determine K-sf. The stiffness Ksf is equivalent to the series stiffness of the discs of the rotor segment with flexural stiffness of K-d and a spring with bending stiffness of K-cc in the location of the contact interface, so K-e is equal to the series stiffness of K-ee and K-cf in the second contact state. The results of a simplified rod-fastened rotor indicate that for a flied pre-tightening force, K-ee decreases with bending moments in the first contact state whereas increases with bending moments in the second contact state. In addition, K-c and K-c decreases abruptly with the increase of bending moments in the second contact state when the rotor is subjected to a relatively large pre-tightening force. Finally, the multipoint exciting method was used to measure the modal parameters of the experimental rod-fastened rotor It is found that the experimental modal frequencies decrease as the pre-tightening force decreases.

Effect of Steel Belt Thickness on Stiffness Charictoristics of Multilayers Waveshape Rotor Damper

A Simplified Analytical Model for U-shaped Steel Dampers Considering Horizontal Bidirectional Deformation

Modal Frequency and Stability of Rotor System Supported by Viscoelastic Elastomeric Dampers

Research On Dynamic Characteristics Of A Magnetorheological Damper With Decoupling Mechanism

Research on Improved Magnetorheological Damper for Wide-Band Vibration Control

Dynamic Characteristics and Modeling of A New Magnetorheological Damper for Broadband Vibration Control

Modeling of Micro-Friction in A Multi-Layer Metal Plate Damper for A Rotor Support System

Experimental Research on Thickness Influence on Isolation Characteristics of Multilayer Circle Metal Plate Damper

Dynamics of A Rotor Supported on Magnet-Rheological Fluid Squeeze Film Damper

Calculation of Multi-Layer Plate Damper under One-Axial Load

VIBRATION CONTROL OF ROTOR SYSTEM BY DISK TYPE ELECTRORHEOLOGICAL DAMPER

Local Linearization Modeling Method of a Multilayer Wave-Shaped Steel-Belt Damper （MWSD）

Research on Damper with Multilayer Steel Plates Modeling and Simulation of Isolation System

Establishment of a contact stiffness matrix and its effect on the dynamic behavior of rod-fastening rotor bearing system

Analysis of Dynamic Performance of Metal Rubber Damping Ring Applied in High-Speed Rotor System

Hysteretic Performance Test and Simulation Analysis of A New Type of Mild Steel Damper

Effects Of Bending Moments And Pre-Tightening Forces On The Flexural Stiffness Of Contact Interfaces In Rod-Fastened Rotors

Numerical investigation of roller steel damper for bridges

Research on the Mechanical Model and Hysteresis Performance of a New Mild Steel-Rotational Friction Hybrid Self-Centering Damper

Study on Experiment and Modeling of Viscoelastic Damper Considering Interfacial Effect of Matrix Rubber/Carbon Black

Experimental and Theory Analysis on the Dynamic Characteristic of Flow-mode MRF Single-end Twin-tube Damper