Abstract:Numerical modeling of heavily-erbium-doped fluoride fiber lasers is presented. Calculations from the model were compared with all previously reported experimental demonstrations of heavily-erbium-doped fluoride fiber lasers. Commensurate with recent modeling studies, good agreement with the measurements was achieved with the use of scaled-down rate parameters for energy transfer that corresponds to weaker interactions between Er3+ ions. For wavelength-fixed (grating) systems, we show that the measured saturation of the output power results from a combination of changes to the Boltzmann distribution arising from core temperature excursions and pump excited state absorption (ESA). In free-running systems, we show that inter-Stark level transitions that terminate on progressively higher Stark levels within the I-4(13/2) manifold in part describe the non-saturating behavior of the output power at moderate pump levels. The model was used to investigate the influence of dopant concentration, pump wavelength, pump configuration, output coupling and background loss of the fiber on laser performance. In contrast to a number of previous modeling investigations, our results show that the slope efficiency steadily increases with increasing erbium concentration as a result of the reduced rates of energy recycling caused by the weakly interacting Er3+ ions. The highest slope efficiency was obtained for a pump wavelength of 983 nm due to reduced levels of ESA, however, for both free-running and wavelength-fixed arrangements of the laser, pump ESA may ultimately preclude significant power scaling.

Modeling of $S$-Band Amplification for Tm$^{3+}$-Doped Fluoride Fiber with Cooperative Lasing at 1.8 $\Mu$m

Numerical Simulation Of 980 Nm-Ld-Pumped Yb3+-Er3+-Tm3+-Codoped Fiber Amplifier For 1500nm And 1600nm Bands

Numerical Simulation of 980 nm-LD-Pumped Yb 3 +-Er 3 +-Tm 3 +-Codoped Fiber Amplifier for 1500 nm and 1600 nmBands

Numerical Model of an Er3+-Tm3+-Pr3+-codoped Fiber Amplifier Pumped with an 800 Nm Laser Diode.

Gain optimization and data modeling of S-band of Tm-doped fiber amplifier based on genetic algorithm

Modeling Erbium–thulium-Co-doped Fiber Amplifier for 1400–1650 Nm Band

Proposal of a Pr^3+-doped telluride fiber amplifier for 13, 149, and 16 μm transmission windows

Proposal Of A Pr3+-Doped Telluride Fiber Amplifier For 1.3, 1.49, And 1.6 Mu M Transmission Windows

Theoretical Characterization of the Ultra-Broadband Gain Spectra at $\sim$1600–2100 Nm from Thulium-Doped Fiber Amplifiers

Modeling and Gain Properties of Er^3+ and Pr^3+ Codoped Fiber Amplifier for 13 and 15 Μm Windows

Theoretical and experimental researches on gain-switched Tm3+-doped fiber laser

Proposal of a Pr3+-doped telluride fiber amplifier for 1.3, 1.49, and 1.6 microm transmission windows.

Optimization of Multiple Active Ion Doped Fiber Amplifiers for Three Communication Windows

Theoretical modeling of Tm-doped silica fiber lasers

Numerical Modeling and Optimization of Mid-Infrared Fluoride Glass Raman Fiber Lasers Pumped by $\hbox{tm}^{3+}$ -Doped Fiber Laser

The comparative study of high efficiency of Tm^{3+}-doped fiber laser at 1.72 μm for different pump schemes

Numerical Modeling and Optimization of Diode Pumped Heavily-Erbium-Doped Fluoride Fiber Lasers

Modeling of Er&#x000B3;+-Ce&#x000B3;+-Doped Telluride Fiber Amplifier

Gain Characteristics of 980 Nm-Pumped Er 3+ –tm 3+ –pr 3+ -Co-doped Fiber

Numerical Modeling and Optimization of Mid-Infrared Fluoride Glass Raman Fiber Lasers Pumped by <formula formulatype="inline"><tex Notation="TeX">$\hbox{Tm}^{3+}$</tex></formula>-Doped Fiber Laser

Simulation Characteristics of Yb3+-Doped Double-Clad Fiber Amplifier for 1053 Nm Pulse Amplification