Abstract:Purpose: The purpose of this study was to exploit potential methods of surface modification for improving the seal between the neck portion of a dental implant and the surrounding soft tissue. Materials and Methods: Titanium surfaces were modified by machining (SM-Ti group); machining and acid etching (AE-Ti group); or machining, acid etching, and depositing 4.5 collagen/hyaluronic acid (col/HA) polyelectrolyte bilayers (CHC-Ti group). These were analyzed using scanning electron microscopy, scanning force microscopy, x-ray photoelectron spectroscopy, contact angle measurement, and quartz crystal microbalance measurement. The degradation behavior of the col/HA multilayer coating was measured. Next, human gingival fibroblasts (HGFs) were cultured on the different surfaces, and cell morphology and spreading were observed using fluorescence microscopy and a shape factor measurement. Cell proliferation was examined by fluorometric quantification of the amount of cellular DNA. Matrix formation of HGFs was determined via enzyme-linked immunosorbent assay. Gene expression was analyzed via reverse transcriptase polymerase chain reaction. Results: Similar surface topology for these three groups was observable on a microscopic scale, and morphologic differences were apparent on the nanoscale. Both acid etching and col/HA deposition improved the hydrophilicity of the titanium surface, in contrast to machining alone. Each col/HA bilayer was about 5 nm thick. The col/HA coating degraded in about a week. Attachment and spreading of HGFs was better on the CHC-Ti surface than on the SM-Ti or AE-Ti surfaces. Moreover, the proliferation and differentiation of HGFs were greatly stimulated when cultured on CHC-Ti. Conclusion: In contrast to two control surfaces (one machined, one machined and acid-etched), col/HA treatment of Ti improved the attachment, spreading, proliferation, and differentiation of HGFs. Int J Oral Maxillofac Implants 2011;26:1183-1192

[Analysis of the surface roughness and bacterium adhesions on the surface of restorative materials in vitro].

Research on correlation between Streptococcus mutans'adhesion and surface roughness of Cu-Al alloy and Co-Cr alloy

[Study of the Correlation Between Streptococcus Mutans' Adhesion and Surface Corrosion in Casting Titanium and Ti Alloy].

Adhesion of different bacterium to the surface of restorative materials in vitro]

Influence of candida albicans'adhesion on corrosion of Ti alloy and Co-Cr alloy

Analysis of the bacterium adhesions on the surface of PFM materials in vitro]

Bacterial adhesion affinities of various implant abutment materials

Effect of different inorganic antibacterial agent on bacteria adhesion of nano-enhanced polymethymethacrylate denture base resin

Surface roughness associated with bacterial adhesion on dental resin-based materials

Effects of surface properties of polymer-based restorative materials on early adhesion of Streptococcus mutans in vitro

Relevance of surface characteristics in the adhesiveness of polymicrobial biofilms to crown restoration materials

Surface Modification And Its Effect On Attachment, Spreading, And Proliferation Of Human Gingival Fibroblasts

Comparison of bacterial adhesion and biofilm formation on zirconia fabricated by two different approaches: an in vitro and in vivo study

Effects of surface roughness and texture on the bacterial adhesion on the bearing surface of bio-ceramic joint implants: An in vitro study

Role of the Surface Nanoscale Roughness of Stainless Steel on Bacterial Adhesion and Microcolony Formation

Bacterial adhesion on smooth and rough titanium surfaces after treatment with different instruments

Comparative evaluation of surface roughness and bacterial adhesion on two bioactive cements: an in-vitro study

The Effects of Dental Hygiene Instruments on Streptococcus sanguinis Adhesion to Titanium Implant Abutments

Research Progress on Factors Affecting Bacterial Adhesion on the Oral Implant Surface

Adhesion of oral microorganisms on three different denture base resins

Bacterial adhesion and surface roughness of particulate-filled and short fiber-reinforced composites