Abstract:Purpose: To evaluate the shear bond strength (SBS) of resin composite to dentin contaminated with artificial saliva (AS) containing mucin and amylase using an experimental method controlling the volume of saliva and adhesive in a defined surface area. Methods: Flat bonding surfaces were prepared on extracted human molars (320 grit surface). Using adhesive tape, a 4.5 mm bonding window was prepared on the dentin surfaces. Groups (n= 12) were prepared using the etch & rinse (ER) or self-etch (SE) modes for Adhese Universal (ADH), Scotchbond Universal Plus (SBU), and Prime & Bond active (PBA) dental adhesives (DA). For the control (C) groups, the adhesives were applied per the manufacturers' instructions with 2.0 µl or 3.0 µl of the adhesive. For the saliva-contaminated groups, 1.0 µl of artificial saliva with mucin was applied in the bonding window either dried or allowed to remain wet before the application of either 2.0 µl or 3.0 µl of the adhesive. After the adhesive film was air dried and light cured using an Ultradent bonding fixture, Spectrum TPH3 was bonded to the prepared surfaces. After water storage for 24 hours at 37°C, the specimens were debonded and shear bond strength (SBS) was calculated (MPa). A Kruskal-Wallis test with Bonferroni correction was used to determine group differences (P< 0.05). Scanning electron microscopy (SEM) was performed to visualize the interfacial surfaces prepared using an ion-etching technique. Results: Mean SBS for the three adhesives were similar in both ER and SE modes to uncontaminated dentin surfaces for all the control groups. For dentin contaminated with dried or wet saliva, both the surface condition and the adhesive system were significant factors at a confidence level of 95%. For the dried saliva test groups, ADH and PBA with 3.0 µl of adhesive generated similar SBS values to controls while SBU generated lower values. Lower values were generated when using 2.0 µl of adhesive for the three adhesives in SE and ER modes except for PBA in the ER mode. Using wet saliva and 3.0 µl of adhesive ADH and SBU generated lower SBS values while PBA generated similar values to controls. Under SEM, morphology at the adhesive dentin interfaces was similar among the adhesives to uncontaminated dentin but notable differences were observed for SBU and ADH for both wet and dried saliva-contaminated surfaces. Clinical significance: Salivary contamination differentially affects shear bond strength and the morphology of the bonded interface of universal adhesives to dentin. These differences are specific to the adhesive tested and are influenced by using the etch and rinse or self-etch strategies and the volume of adhesive used. When concerned about salivary contamination clinically, maximizing the volume of adhesive on the substrate may help mitigate the deleterious effects of saliva contamination.

Adhesion of oral microorganisms on three different denture base resins

Durability of Four Composite Resin Cements Bonded to Dentin under Simulated Pulpal Pressure

Influence of Casein Phosphopeptide-Amorphous Calcium Phosphate Application, Smear Layer Removal, and Storage Time on Resin-Dentin Bonding

Bonding Quality of Etch-and-Rinse Adhesives in Root Canals Upon Different Pretreatments.

Evaluation of adherence of Candida albicans to differently manufactured acrylic resin denture base materials

Effect of Chemical Removal or Mechanical Modification of Smear Layer on Dentin Adhesion with Universal Resin Adhesives

Effect of direct tooth-colored restorative materials on early adhesion of Streptococcus mutans

Influence of Polymerization Protocol on Adhesion and Proliferation of Streptococcus mutans on Three Dental Composite Resins

Effects of surface properties of polymer-based restorative materials on early adhesion of Streptococcus mutans in vitro

Effect of build angle, resin layer thickness and viscosity on the surface properties and microbial adhesion of denture bases manufactured using digital light processing

Experimental Study on Bacteriostasis in Vitro of Longliqi DL Toothpaste Containing Compound Enzyme on Several Species of Oral Bacterium

Influence of Removable Denture Cleaning Agents on Adhesion of Oral Pathogenic Microflora In Vitro: A Randomized Controlled Trial

Effects of Two Peroxide Enzymatic Denture Cleaners on Candida Albicans Biofilms and Denture Surface.

[Antibacterial Effect of Self-Etching Adhesive Systems on Streptococcus Mutans].

Cross-compatibility of methacrylate-based resin composites and etch-and-rinse one-bottle adhesives

[Effects of Three Self-Etch Adhesives and Mild Salivary Contamination on the Bonding Durability of Deciduous Teeth].

Bacterial adhesion and surface roughness of particulate-filled and short fiber-reinforced composites

Effect of Smear Layer Prepared by Different Burs on the Microtensile Bond Strengths of Two Kinds of Adhesive Systems to Human Dentin

Effects of salivary contamination on the shear bond strengths of universal adhesives to dentin

Evaluate the Effect of Different Mmps Inhibitors on Adhesive Physical Properties of Dental Adhesives, Bond Strength and Mmp Substarte Activity

Antibacterial effect of Softsoap used to disinfect dentures