Abstract:There are many sand-laden waters in China, and the wear of hydraulic structures caused by sand-laden water diversion has been paid more and more attention. Taking the spillway of a reservoir as the research object, the numerical model of erosion wear caused by sediment-laden particle flows on the spillway was established by using the computational fluid dynamics (CFD) method, VOF (Volume of Fluid) multiphase flow model and DPM (Discrete Phase Model). Through the simulation analysis of the spillway’s overall erosion, the distribution of the spillway erosion wear was obtained. Then, according to the main wear parts, the single variable, such as sediment diameter, sediment concentration, flow velocity and gate opening degree, was changed to study the erosion amount of the spillway and the distribution law of the spillway erosion parts. The results show that the main erosion sites of the spillway are at the bottom of the gate chamber and the middle section of the spillway. The maximum erosion increases linearly with the increase in sediment concentration. With the increase in sediment concentration, the sediment concentration changed from 1 kg/m3 to 6 kg/m3, and the maximum erosion of the spillway increased from 2.58 × 10−7 kg/m2 to 1.53 × 10−6 kg/m2. The erosion at the bottom of the spillway and gate leaf increases first and then decreases with the increase in sediment diameter and reaches the maximum value when the particle size is 0.002 mm. The erosion at the bottom of the spillway and the gate leaf increases with different growth trends as the flow velocity increases, when the flow velocity increases from 2 m/s to 9 m/s and the maximum erosion amount at the bottom of the spillway increases from 3.66 × 10−7 kg/m2 to 1.14 × 10−6 kg/m2, and the maximum erosion of the gate leaf increased from 1.66 × 10−8 kg/m2 to 8.98 × 10−6 kg/m2. The erosion amount at the bottom of the spillway increases with the increase in the gate opening between 0 and 3 m and tends to be stable when the gate opening is greater than 3 m. The maximum erosion position moves to the rear part of the spillway with the change in the gate opening. The change in the gate opening has no obvious effect on the erosion amount of the gate leaf but only changes the area of the gate erosion part. Thus, the erosion wear distribution of spillway under different work conditions is summarized, and the qualitative study between the erosion wear and the distribution of sediment diameter, sediment concentration, flow velocity and gate opening degree is made.

Research on Erosion Wear to Water Lubricated Spiral Groove Rubber-Alloy Bearing Caused by Sand Particles

Simulation Analysis for Lubrication State of the Thrust Washer Within Straight Planetary Gear Set

Mechanisms of abrasive wear in lubricated contacts

Finite element simulation and experimental test of the wear behavior for self-lubricating spherical plain bearings

Abrasion Simulation of a Reciprocating Seal

Investigation of Factors Affecting Wear Characteristics in Rubber–Metal Sliding Contact

Effect of Particle Size on Tribological Properties of Rubber/Steel Seal Pairs Under Contaminated Water Lubrication Conditions

Study on Tribological Behavior of Grooved-Texture Surfaces under Sand–oil Boundary Lubrication Conditions

Numerical Investigation of Erosion Wear Characteristics of Hydraulic Spillway

A Study of the Relationship between Sand Movement and Flow Field Distribution and Wear Causes in a Multiphase Pump

A Mixed Lubrication Model for Predicting the Lubrication Performance Degradation Behavior of Slipper Pair in Early Wear Failure

The Fem Analysis Of Rolling-Sliding Contact Under Boundary Lubrication'S

Current Situation and Prospect of Erosion Wear

Influence of anisotropic surface roughness on lubricated rubber friction with application to hydraulic seals

A Deterministic Mixed Lubrication Model for Parallel Rough Surfaces Considering Wear Evolution

Evolution of tooth surface morphology and tribological properties of helical gears during mixed lubrication sliding wear

Tribological Performance of Differential Gear End-Face Sliding on Washer with a Radial Groove

Experimental Study on Deteriorated Performance, Vibration, and Geometry Changes of an Electrical Submersible Pump Under Sand Water Flow Condition

Effects of Surface Texture on Turbulent Lubrication of Water-lubricated Journal Bearing

Simulation of Sliding Wear in Mixed Lubrication

Surface Roughness Effect on the Friction and Wear Behaviour of Acrylonitrile–Butadiene Rubber (NBR) Under Oil Lubrication